What did you do to your NNBS GMT900 Tahoe/Yukon Today?

[89Suburban]

I used a

if there is enough plastic left just leave it and slide the new hose over it, if it is already broken off too short then you will have to replace the T

Yup! Get the rest of the broken piece off the tee and just clamp right onto it.

 

[Kee Fuller]

Got it off. Jesus thst was a pain in the ass

 

[Fosscore]

Installing new Moog endlinks K700538.

Going to check and make sure the correct part number but that other bushing has zero space to slide in the spacer before passing through the control arm.

Truck is jacked up with both front wheels off the the ground. Hmmm...??

Exact same set up on my Tahoe. What am I missing here?





Edit: checked part number and application for 2007-2014. Sleeve length shows 3.4 inches.

 

[89Suburban]

Got it off. Jesus thst was a pain in the ass

On the side of the road in a rain storm with a half gallon jug of coolant, THAT is a pain in the ass. I keep a straight barb fitting and some clamps in the truck in case it happens again just to bypass that crap to make it home in an emergency. And a FULL gallon of coolant lol...

 

[gooffeyguy]

Installing new Moog endlinks K700538.

Going to check and make sure the correct part number but that other bushing has zero space to slide in the spacer before passing through the control arm.

Truck is jacked up with both front wheels off the the ground. Hmmm...??

Exact same set up on my Tahoe. What am I missing here?


View attachment 233749


Edit: checked part number and application for 2007-2014. Sleeve length shows 3.4 inches.

View attachment 233750

I did mine with the front wheels on ramps. I removed both sides which allowed the sway bar end to rotate up/down. I installed the new endlinks up from the bottom and used the barrel nut end on the top.

2001 Yukon SLT
2012 Yukon Denali XL
2011 Yukon Denali RIP 5/20/18

 

[PPV12HOE]

Installing new Moog endlinks K700538.

Going to check and make sure the correct part number but that other bushing has zero space to slide in the spacer before passing through the control arm.

Truck is jacked up with both front wheels off the the ground. Hmmm...??

Exact same set up on my Tahoe. What am I missing here?


View attachment 233749


Edit: checked part number and application for 2007-2014. Sleeve length shows 3.4 inches.

View attachment 233750

Undo both sides and the sway bar will rotate up giving you the room to install them...

 

[Fosscore]

Undo both sides and the sway bar will rotate up giving you the room to install them...

Thx guys. Guess I got in a hurry to get it done before dark and the gym. Got the passenger side in, but the reverse way you would normally do it. And it took some negotiating. lol. What a dummy!! Will unload the other side and get it sorted in a few hours and update.

Waited all day to get the part, then kids come home and you know how it goes.....lol.

 

[Kee Fuller]

this piece on both sides, then you can try squeezing the white clip in and then pull on the connector

View attachment 233744

Welp ran into another issue. The new hose snaps into the white clips, but now its leaking coolant there

 

[89Suburban]

Welp ran into another issue. The new hose snaps into the white clips, but now its leaking coolant there

So you replaced the whole hose with the new fitting and it is leaking out of the O-Ring on the fitting? Maybe the Tee itself is cracked too?? Not sure if I follow here.

 

[PPV12HOE]

Thx guys. Guess I got in a hurry to get it done before dark and the gym. Got the passenger side in, but the reverse way you would normally do it. And it took some negotiating. lol. What a dummy!! Will unload the other side and get it sorted in a few hours and update.

Waited all day to get the part, then kids come home and you know how it goes.....lol.

Yup I just picked mine up from afterschool now it's time to make dinner...