My Bermuda Blue Hoe

[Goodinblack]

Nice start

Sent from my SM-N910V using Tapatalk

 

[Tonyrodz]

I'm liking this thread already. The mods def bleed you dry, so you have to figure out what you'd like more. I went with speed myself.

 

[Shaw520]

I like where this is going, nice build. The unit above the cb, is that a booster or RF gain ?

 

[Jlaughtr]

I like where this is going, nice build. The unit above the cb, is that a booster or RF gain ?

Not sure to be honest. Just found this pic online and thats what I'm going to go for. Might talk to a CB place and see what they think it is and see if its needed when the time for that mod comes

 

[Jlaughtr]

A few aesthetic Mods to do this weekend.
1) A all aluminum billet black Chevy emblem

2) All aluminum Billet 50 Cal Bullet Antenna. Wasn't ready for the antenna delete Mod until I upgrade the stereo, but this is a cool look until I decide.

 

[Jlaughtr]

I'm liking this thread already. The mods def bleed you dry, so you have to figure out what you'd like more. I went with speed myself.

Yea. My mods are slowly coming. Performance mods are usually the most expensive so have to save up haha

 

[swathdiver]

View attachment 196842

Careful with this around school parking lots and zones, they'll freak out and have the driver arrested! Looks great!

 

[Goodinblack]

About got one of those antennas they said they gave poor reception though

Sent from my SM-N910V using Tapatalk

 

[Jlaughtr]

Careful with this around school parking lots and zones, they'll freak out and have the driver arrested! Looks great!

Hahahaha damn snowflakes! Haven’t put it on yet. That’s just the stock photo from amazon. I’ll post pics this weekend

 

[Jlaughtr]

About got one of those antennas they said they gave poor reception though

Sent from my SM-N910V using Tapatalk

Yea the reviews were mixed. But I’ll keep you posted on the reception. I drive a lot on trips so I’ll have a good test

 

[Jlaughtr]

Got the 50 Cal Antenna on this morning. Pretty easy install. Had take off the plastic piece that cover the antenna area, couple together 2 adapters and put them onto the antenna screw, replace the plastic piece. Then finish it off by screwing on the antenna! Super simple. Looks cool. Stay tuned for reception testing over the next week or 2

 

[Jlaughtr]

So far signal is unchanged. But I haven’t left the normal city areas

 

[Shaw520]

Nah,... yall have ta get er up to around 3000 feet per second before you can tell.....

 

[Goodinblack]

Linex and the black is awesome compared to that faded gray

View attachment 195534 View attachment 195535 View attachment 195536 View attachment 195537 View attachment 195538

How hard were to lower side pieces to remove?

Did you break any tabs etc?

I want to do this for my Z.

 

[Jlaughtr]

How hard were to lower side pieces to remove?

Did you break any tabs etc?

I want to do this for my Z.

So I took it to the lined shop to have it done. So I can’t attest to the removal process

That being said they didn’t put all the clips back in the front valence. So tonight I was trying to put in all brand new clips from amazon for the valence. They DO NOT WORK!! They are not the right length. So the clips are tough to get out in some spots and you might break them. Currently I have a zip tie job for my valence until I get the right clips.

I did not attempt or take off any of the other panels so I don’t know about those

 

[Jlaughtr]

New black Emblem

 

[Goodinblack]

So I took it to the lined shop to have it done. So I can’t attest to the removal process

That being said they didn’t put all the clips back in the front valence. So tonight I was trying to put in all brand new clips from amazon for the valence. They DO NOT WORK!! They are not the right length. So the clips are tough to get out in some spots and you might break them. Currently I have a zip tie job for my valence until I get the right clips.

I did not attempt or take off any of the other panels so I don’t know about those

Okay thank you

Sent from my SM-N910V using Tapatalk

 

[Jlaughtr]

Okay thank you

Sent from my SM-N910V using Tapatalk

If you are going to remove all the panels, I personally would get all new clips. Even if you manage not to break them, I think newones would hold better because of the age of the plastic. I have the part numbers for all the clips from the chevy dealership.

 

[Goodinblack]

If you are going to remove all the panels, I personally would get all new clips. Even if you manage not to break them, I think newones would hold better because of the age of the plastic. I have the part numbers for all the clips from the chevy dealership.

Ah cool. Please pm them to me if you can

Sent from my SM-N910V using Tapatalk

 

[Fosscore]

Nice work so far.