What did you do to your OBS GMT400 Tahoe/Yukon Today?

[rabbiporkchop]

Any good consoles that would accommodate a manual transmission?

I like my Tuffy console. It can be mounted further back and without the drink holder if necessary. NV4500 to come in the future.

 

[noJeepshere]

My console is a factory one from a 92 2-door with a 5 speed.

cent frum a smaert fone

---------- Post added at 12:10 PM ---------- Previous post was at 12:09 PM ----------

Wow, you never really pay attention to how bad things look until you post a picture of them, my carpet is baad! as is the arm rest.

cent frum a smaert fone

 

[chaingun427]

Found a 411 at the pull a part, trading my old uneeded 4l60e for it. Getting the entire mounting bracket as well as they plugs and some wire. Wondering if I can do a stepper fuel gauge with this pcm...

 

[95escahoe]

Ordered a new Delphi fuel pump

 

[99YukonSLT]

In the last week while tracking down my cram/crank correlation issue along with a much needed tuneup...

Plugs, distributor, timing chain (old was VERY loose), flowmaster cats, Gibson exhaust, water pump. Then I noticed the intake manifold was leaking a little

 

[Goodinblack]

New Poll is up

Vote Now

A big Thank you to our Sponsor this month

NorcalSS

http://tahoeyukonforum.com/forum/showthread.php?t=71633

 

[MrBob]

Replaced the passenger side window motor, not a bad job, just not exciting.

 

[bigal11419]

Installed new mode door actuator, Goodyear gatorback belt and new anzo led twilight assemblies

 

[mattss90]

Ive done a lot this weekend. Thank you tax returns!

1)dropped my hoe off at a lift shop. Getting a 6" BDS lift put on her.

2)Ordered some 16x10 mickey thompson classic IIIs to go with it

3)and 35x12.5r16 mickey thompson MTZ Radials to put on the rims.

4) then ordered new side mirrors (probably going to paint those to match)

5)ordered hoop steps for both passenger and driver sides

6)ordered a new air valance... ive cracked mine twice now

7) just received my white side markers that ill throw on when i get the truck back from the shop this week.

8)put on this black and gold Tahoe hitch plug

so yea... ive done a lot, but got a lot more to do when all my parts come in. Gonna have a blast installing all of this stuff next weekend.

 

[95escahoe]

Ordered a new driverside leather seat bottom & foam bottom

 

[GTOHOE]

Installed a new steering gear box and pitmen arm steering speed sensor Moog ball joints upper and lower, also picked up a energy suspension hyper flex master kit since I had to remove the A arm's. Getting around to install the 14 bolt 6 lug rear end just had it gone through and blasted and painted I'll probably swap them as I install the 6" lift.. also got my new rockers and lower front quarters to weld in. Then off to the paint Booth..

 

[Sharpieferrari]

I had turbo mocked up today. Almost done with my baby!

 

[chaingun427]

Got the front carpet and all seats pulled to get it cleaned. found out that with some creative stacking all 4 seats will fit inthe rear cargo area

Finished under dash wiring for neutral safety switch, DIC overhead console, and steering wheel controls. Amp wiring tomorrow. Trying to decide where I want to put it, and if I just plain want to replace the thing.

 

[mattss90]

went from this

to this... yesterday

 

[jerryjoe28]

^ looks good!

 

[bigal11419]

Installed new idler pulley and tensioner pulley as well as new PIAA horns. Started hunting down an annoying whistle from the engine bay.

 

[chaingun427]

Got the bad motors accessories stripped, and it's unbolted. Now I need it to dry up so I can get the motor pulled

 

[bigal11419]

Installed a Volant Cold Air Intake and continued hunting down my under-hood whistle

 

[ryanm1987]

on Friday I got the front end of my 97 Tahoe 4x4 rebuilt with all mevotech supreme parts idler arm, idler arm bracket, inner tie rod ends, outer tie rod ends, kyb monomax front shocks, and whole upper control arms made by mevotech they have 2 different part numbers economy line and the supreme line which is what I got I got all that done for $400 cash and $50 for a alignment. Drives like new do you all think that was a good price to have that done, It was a friend that owns a shop he said anyone else it would of been $800 or more I think I got a good deal

 

[chaingun427]

What was your part cost? Im looking to get the same done on the project hoe soon as the engine is in