-
-
skpyle posted the thread Any value in a set of good used 2-piston calipers and brackets from a GMT900? in Engine & Drivetrain.Hello All! Wandered over here from the 2007-2014 forum. I recently upgraded the brakes on my 2013 Escalade ESV. As such, I have the... -
-
skpyle replied to the thread 6L80 Sonnax ZIP Kit, Pressure Switch rebuild, remote filter install, and fluid flush in 2013 Escalade ESV (Pic heavy).Heheheheheheh. My Red Witch is proof I know how to waste money for no real purpose or gain.
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.You are quite welcome!
-
skpyle replied to the thread 2013 Escalade ESV Next BIG adventure: Cooling system refresh, Big 3 Electrical upgrade, Reseal intake, and VLOM mod....Noosir. Not yet. I will be overhauling the rear brakes in the near future. With the rear wheels off, I plan to remove the right rear...
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.I do not. I have been daily driving my Escalade with this brake conversion on the stock master cylinder. No issues. There is no...
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.Nice! A little late now for me... :D
-
skpyle replied to the thread Has anyone used a 24284077 Torque Converter (6L90?).If your CVC billet reman is the BU60FHD, I'll gladly buy it...
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.The stock 2-piston floating calipers, brackets, and pads are all in excellent condition. Do you guys think the GMT800 crowd would be...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.16" rotor and Brembo caliper do a nice job of filling up the 22" wheel. With the front end finally back together, I took my Escalade...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.15mm thick hub centric wheel spacers with 6 on 5.5" pattern. I purchased them on Amazon. They are forged and have good review. We shall...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.I didn't feel like the ball joint separator fully seated the new lug stud. Washer, spacer, and lug nut used to fully seat the new...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.Alright, we have established that the new calipers are too fat for the stock wheels to fit. Spacers and longer lug studs are needed...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.Agreed. When I was researching this project, I saw reports that rotors from various manufacturers were in short supply.
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.While getting my pressure bleeder set up and doing general clean-up, I let the calipers gravity bleed for awhile. Didn't really do much...
-
-
skpyle replied to the thread 2021 PPV Front Brakes on 2013 Escalade ESV, and rear brake overhaul.I mounted the assembled brake calipers with the new mounting bolts and correct spacers. The mounting bolts and spacers were fiddly...
-
-
-
Loading…
-
Loading…
