What did you do to your NNBS GMT900 Tahoe/Yukon Today?
- Thread starter phattyford
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Tonyrodz
Resident Resident
Swapped out my front brake pads.
New ones went in with zero issues, though I have not bedded them in, yet.
That will be done in the morning.
Greased the outer tie rod end while I had the wheels off.
Sure wish my Husky mud flaps had been delivered so I could have installed those while I had the wheels off.
New ones went in with zero issues, though I have not bedded them in, yet.
That will be done in the morning.
Greased the outer tie rod end while I had the wheels off.
Sure wish my Husky mud flaps had been delivered so I could have installed those while I had the wheels off.
LowCountryTim
Member
Took the wiper arms and cowl off and game them a coat of trim black:
Replaced the passenger side motor mount.. that was actually fine:
Replaced the passenger side motor mount.. that was actually fine:
I swapped out my front pads yesterday as well. It was glorious zero issues after my ordeal with the rears last month. We leave on a three week camper trip today.Swapped out my front brake pads.
New ones went in with zero issues, though I have not bedded them in, yet.
That will be done in the morning.
Greased the outer tie rod end while I had the wheels off.
Sure wish my Husky mud flaps had been delivered so I could have installed those while I had the wheels off.
Paintbull.com
PB Headlight Re-Supply Kit – Paint Bull Supply
store.paintbull.com
I'm torn. these lens guard film I have says uv protection as well as rock chips so I do want to install it. I wonder if I could put it over the clear slick.
blah. plus I need to get these installed so I can return the old ones soon.
CMoore711
Full Access Member
- Joined
- Jul 18, 2017
- Posts
- 1,577
- Reaction score
- 1,503
Did you do any prep on the wiper arms or cowl before you painted them? Did you sand them at all? Use any primer or just the Trim Black paint?
I could see sanding the wiper arms a bit, but not sure about the cowl?
LowCountryTim
Member
On the cowl I scrubbed with a green scuff pad and dawn dish detergent, rinsed and then wiped with an IPA solution (carpro eraser). Then sprayed.
On the wipers I scrubbed with scuff pad then sanded with 320 grit. SEM says use 400 grit, but it's what I had.
Two coats on all. I'll polish the wipers in a week or so. SEM does not call for a primer.
mikez71
Full Access Member
- Joined
- Mar 9, 2023
- Posts
- 3,244
- Reaction score
- 4,016
Well, my mud flaps showed up today, a mere 18 hours or so after I had the front wheels off for brakes.
Don't know if I'll take them off again.
But, it is time to tackle the steering angle sensor.
Time to become a contortionist and work under the dash for a few hours.
Don't know if I'll take them off again.
But, it is time to tackle the steering angle sensor.
Time to become a contortionist and work under the dash for a few hours.
I need one of those!
Got the steering position sensor done.
Zero errors when the steering wheel is turned.
Mission accomplished.
And yes, the inside still needs to be cleaned up.
It showed up completely dirty inside, have not had a chance to detail the inside.
Attachments
![20240609_195415[1].jpg](/data/attachments/424/424378-2f1f8278d86d1831c6195afb8814ac9e.jpg)
![20240609_195431[1].jpg](/data/attachments/424/424379-43ad44ec6eaedf8e6e30d7c58d6864f5.jpg)
Last edited:
blackelky
Full Access Member
- Joined
- Oct 15, 2023
- Posts
- 586
- Reaction score
- 770
Moved to the country
RichardCranium
Full Access Member
Rolling pics, here is a teaser I got from the photog.
Gave it a bath this morning and checked all of the tire pressures.
Finally got the chance to vacuum the interior.
Finally got the chance to vacuum the interior.
OK, so how do I use this stuff on new headlights?
I figure I'll just do all 3 of my cars if it turns out well.
Tonyrodz
Resident Resident
You'll be pleased with the results--as long as it's properly applied. For older hazy lights you'd need to restore them 1st before applying this.
cleaned the tb and reset the idle after replacing some factory wire loom that was turning to dust, so had the air intake off. funny the only bad loom is what runs across the water pump. I've been half temped to put a little cooler stat in this thing for a while. I know they say it's not needed but being 115deg here and running 87. I feel like a 7-10deg cooler stat might help and definitely not hurt. really wish I had timing vs intake air temp table in hpt. blah.
debating sending off oil and trannys samples, but just 3k on the oil and 10k since the tranny fluid change. feels kinda early to get any good data back for the money.
I think I've finally confirmed no hybrid ecm has the capability of doing the virtual flex fuel and definitely won't get the support to enable a add on sensor. shame but it's not just hptuners and other scanners, that's not defined correctly. in the tech 2 not only is there no alcohol content % under fuel system. there's also no way to reset the virtual math under special stuff. I can't imagine they would leave the reset out if it was active
I was always pretty sure, but now I'm 100% sure. should have been obvious, no yellow cap no E. but there's always been disagreement about it. I'm sure since all the hardware is the same, the pumps lines and injectors can handle the alcohol, but the fuel correction just isn't there. not like anyone runs around wot racing in their hybrid, so it probably wouldn't ever hurt anything, but it's not correct.
Suede applicator pads were delivered. so tonight I'm going to try my hand at uv coating these new headlights. let them dry overnight, get them installed tomorrow so can send these old ones back for the warranty refund. going to be an interesting test.
debating sending off oil and trannys samples, but just 3k on the oil and 10k since the tranny fluid change. feels kinda early to get any good data back for the money.
I think I've finally confirmed no hybrid ecm has the capability of doing the virtual flex fuel and definitely won't get the support to enable a add on sensor. shame but it's not just hptuners and other scanners, that's not defined correctly. in the tech 2 not only is there no alcohol content % under fuel system. there's also no way to reset the virtual math under special stuff. I can't imagine they would leave the reset out if it was active
I was always pretty sure, but now I'm 100% sure. should have been obvious, no yellow cap no E. but there's always been disagreement about it. I'm sure since all the hardware is the same, the pumps lines and injectors can handle the alcohol, but the fuel correction just isn't there. not like anyone runs around wot racing in their hybrid, so it probably wouldn't ever hurt anything, but it's not correct.
Suede applicator pads were delivered. so tonight I'm going to try my hand at uv coating these new headlights. let them dry overnight, get them installed tomorrow so can send these old ones back for the warranty refund. going to be an interesting test.
