Where you been?
Pwtr02ss home build
- Thread starter pwtr02ss
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
OP
OP
pwtr02ss
Full Access Member
New fone who dis
randeez
Full Access Member
needs more house
OP
OP
pwtr02ss
Full Access Member
workin on it. hopefully they get started soon.
Glad to see you peaking in. Hope you've been well, homo
randeez
Full Access Member
been busy
OP
OP
pwtr02ss
Full Access Member
still have the V?
How the heck did I miss this thread? 
Well, I have some catching up to do.
Well, I have some catching up to do.
OP
OP
pwtr02ss
Full Access Member
Plans are officially out for pricing, have been since end of last week.
Grading guy moved equipment back out today. He said he's got a dozer back out there and moving an excavator tomorrow. Hopefully get the logs moved offsite and start final (rough) grade. We talked through what I want and I'm going to meet him tomorrow after work if everything goes smoothly.
Slow process
Grading guy moved equipment back out today. He said he's got a dozer back out there and moving an excavator tomorrow. Hopefully get the logs moved offsite and start final (rough) grade. We talked through what I want and I'm going to meet him tomorrow after work if everything goes smoothly.
Slow process
OP
OP
pwtr02ss
Full Access Member
Went out there this afternoon. Freeze thaw is real. Top two inches of the pad were sticky mud. Didn't sink, just slid across it. Muddy mess of an avalanche.
Strapped the muck boots on an we rough staked the shop pad. They gonna have to redo about 50' of fill to get the slopes right for runoff. Not the end of the world, just one more slow down.
They'd started regrading the driveway and right side. It's all still too wet.
We talked through what I want. Hope it'll dry out at some point
Strapped the muck boots on an we rough staked the shop pad. They gonna have to redo about 50' of fill to get the slopes right for runoff. Not the end of the world, just one more slow down.
They'd started regrading the driveway and right side. It's all still too wet.
We talked through what I want. Hope it'll dry out at some point
randeez
Full Access Member
yea couple more things done to it, full bolt-onish at this point, ported blower/103mm tb, had a 10l90 fall in my lap pretty cheap so it got swapped in also still. im having some mystery cyl6/8 misfire/problems i think the head gasket is on its way out. those two plugs look like theyre burning a little coolant, but not enough to notice
OP
OP
pwtr02ss
Full Access Member
Very nice. Bet that ****** rips. Yukon?
randeez
Full Access Member
Yukon has been parked, back to sort of stock ride height.
It runs and drives but needs some refreshing. Engine has been abused for several years and is tired, ring tension is kinda gone, transmission is pretty fresh in it, has a 263hd transfer case in it atm, no front diff, rear pinion needs new crush washer/reset. I bought a holley and some new injectors for it, but it just needs a lot to get it to hold its own with the new wave of trucks/suvs.
OP
OP
pwtr02ss
Full Access Member
Glad to hear you're still wrenching. Missed you around these parts, if you couldn't tell from my months of checking in...fu-cker
Hopefully you'll stick around and I can finally get those parts installed...someday.
Ps, good morning
love is in the air...
OP
OP
pwtr02ss
Full Access Member
Missed my scissor sister
randeez
Full Access Member
OP
OP
pwtr02ss
Full Access Member
Don't look like no Yukon ta me
