Got my 2010 PPV

[Peacock]

...

 

[1BADI5]

So? Just put a cammed 6.2 under that FAST102. Duh.

I know right, I just need a donor with the L94.

But if I found said donor that motor would go into my Colorado

 

[iamdub]

I know right, I just need a donor with the L94.

But if I found said donor that motor would go into my Colorado

I wish I could "just" put a cammed 6.2 in any vehicle just to take advantage of an intake manifold!

 

[1BADI5]

I wish I could "just" put a cammed 6.2 in any vehicle just to take advantage of an intake manifold!

Nope, work smarter not harder. I just returned the intake manifold

 

[1BADI5]

Some small updates and parts in cue for install. New black bowtie up front and my new trans cooler. Just waiting on the brackets and hardware I ordered to install it.

With all of the rain and when washing the PPV I got tried of the water collecting......so 2 drainage holes it is

 

[1BADI5]

Some small updates and parts in cue for install. New black bowtie up front and my new trans cooler. Just waiting on the brackets and hardware I ordered to install it.

With all of the rain and when washing the PPV I got tried of the water collecting......so 2 drainage holes it is

 

[iamdub]

Tru-Cool 40K? I have one on the way. I just saw there is a factory cooler kit (GM Part #19171483) with lines that would work for the Tru-Cool with very little modding. Basically it's just trimming the radiator shroud where the lines would normally run so they can be spread apart to fit the wider cooler.

 

[1BADI5]

Tru-Cool 40K? I have one on the way. I just saw there is a factory cooler kit with lines that would work for the Tru-Cool with very little modding. Basically it's just trimming the radiator shroud where the lines would normally run so they can be spread apart to fit the wider cooler.

Yeah a I ordered the brackets and hardware from a member over on performancetrucks.net

 

[iamdub]

Yeah a I ordered the brackets and hardware from a member over on performancetrucks.net

I just wish I had known about those factory lines before I placed another order. It would've put me over the "free shipping" amount.

 

[Kee Fuller]

Yeah a I ordered the brackets and hardware from a member over on performancetrucks.net

I dont plan on towing, but im thinking bout doing this upgrade just in case

 

[1BADI5]

Well I bit the bullet and ordered the Atomic poly motor mounts and the B&M 70392 deep trans pan since I will doing the trans service and TruCool Max trans cooler next week.

 

[1BADI5]

https://atomicfabandperformance.com...81905354511_5055335013160058880_o-510x383.jpg

 

[1BADI5]

 

[1BADI5]

What better thing to do when bored and have some black 3M vinyl in the garage. Wrap some shit fools.

 

[1BADI5]

I finished the vinyl work and now on to some paint.

Atomic motor mounts and B&M deep trans pan came in today.......and I got stickahs FTW; 10 more rwhp

 

[1BADI5]

Project name "Undercover Sleeper"

Completed (as of 27 APR 2020)

- Texas Speed Long tube headers - 1 3/4 primary/3" collectors
- Texas Speed 3" catless Y Pipe
- Magnaflow muffler 12259
- Rear resonator delete
- Ported LS7 Throttle body (ported by Me)
- Ported OEM intake manifold w/intake manifold gaskets & injector O-Rings (ported by me)
- AiRaid MIT intake tube / AEM dry filter (70k)
- Airbox mod (opened up inner fender and matched the Airbox)
- Cleaned the MAF (70k)
- HPTuners - work in progress
- Denso IR plugs / Taylor 10.4mm plug wires
- Gates HD Green belt, AC belt, idler pulley, auto tensioner
- Atomic Fab Performance solid motor mounts
- Holley powder coated valve covers (Tall) / new braided hoses & inline PCV
- UDR Catch can (black with black braided lines)
- AC Delco Professional 48 series Battery (3/20)
- Royal Purple HMX oil change (70k/75k)
- Royal Purple 75w90 Diff service
- Tru Cooler MAX - 40k Trans Cooler / with custom brackets
- B&M Deep Trans pan - extra 2qts with drain/temp sensor ports
- Trans service (OEM fluid/filter/gasket) (4/20, 75K)
- Replace both Trans cooler lines (AC Delco)
- StopTech SS lines (front/Rear)
- DOT3 Flush
- AC Delco PPV front rotors
- EBC YellowStuff front pads
- Rear pads
- Aerotech gauge with column pod
- Innovate Wideband (in, 4x4 headlight bezel)
- XTRONs HU with backup camera & forward facing camera & GPS
- OEM Remote Start added - RPO AP8, GM part 19154445
- OEM Auto Dimming rear view mirror
- OEM mirrors with signals/puddle light - *needs BCM update*
- OEM DIC install
- OEM Tow/Haul shifter
- OEM Steering wheel Stereo controls
- Grant Leather wrapped OEM wheel w/ fresh OEM spoke covers
- Husky mats - front/back/cargo
- New headlight housings w/ LED HI & Lows
- OEM foglights added - OEM switch/lights and wired
- LED light bar, LED tag bulbs, LED brake lights, LED Dome lights (red)
- BellTech 2/3 drop (spindles/springs)
- Yukon Gear&Axle (3.73 and Dura Grip) (Complete overhaul/rebuild @ 75k)
- Spohn adjustable Panhard bar
- AC Delco Professional front sway bar end links
- Goodyear Eagle Ultra Grip GW-3 - (265/60R17)
- Airhorn install 150+DB

- Dropped the spare tire out, deleted the spare hoist/holder, removed OEM bottle jack and tool kit, removed the spare battery tray, removed about 5 lbs of spare antenna cable from the rear of the truck, removed excess brackets and cabling from under dash


Next up - Ready to install

* OEM PPV shocks/struts & all hardware (ON HAND)
* ATI Harmonic Balancer (For Sale)
------------------------------------------------------------
* Powerbond 25% under drive crank pulley/balancer (Ordered)
* ARP Crank bolt and new belts (Ordered)
------------------------------------------------------------
* Light weight Alternator/PS pulleys
* Rocker Arm upgrade (either TSP or Terra Yella 1.7)

 

[1BADI5]

Parts ordered for a ring/pinion swap and Yukon Gear and axle Dura Grip positraction.

Going to 3.73 since 3.55 ratio was not available from Yukon Gear

Scheduled the install for next week.

 

[GreyStone]

are you replacing the whole axle or just the internals

 

[1BADI5]

are you replacing the whole axle or just the internals

New ring/pinion and locker; plus a complete rebuild (new bearings, races and gaskets)

So same axle housing and axles......but all of the guts are being replaced

 

[GreyStone]

is it a G80