What did you do to your OBS GMT400 Tahoe/Yukon Today?

[slipping]

U did the body lift? Anythong i need to know so i dont **** up anything else?

Yeah I did the body lift. The steering extension acted like it was gonn be a PITA but it was actually easy. I'm push button 4WD so I didn't have to worry about shifter linkage. I've heard that's a b****. The shroud gave me the absolute most trouble, that and relocating the rear bumper.

Are the BLs on the 4wd different than the 2wd? I have taken all my BL off but not sure if mine has the trans cable extender. Gotta take the seat and carpet up, was wanting to know before I took it all up

 

[SunlitComet]

tranny should have a cable but gzes has a manual tcase shifter that must be accounted for.

 

[Gzes]

Tcase i loosened from the top but it didnt shift. On cable trannys theres no extension you jist move it a lil down the hole. Mines rod so i have to weld in an extension. I jist picked up screw extractors so tomorrow im going at it

---------- Post added at 12:57 AM ---------- Previous post was at 12:50 AM ----------

By not shift is sink down but tomorrow im gonna hurry up n get the bolt out and locktite the new bolts and cut ths shroud and put it all together after the rod

 

[_Dylan_]

new pads and rotors

 

[slipping]

Just got done ordering new plugs, wires, cap, rotor and k&n this morn. Walked outside and the wife says "what's under your truck?"

Going back in to order a water pump.

 

[Tricky]

Just got done ordering new plugs, wires, cap, rotor and k&n this morn. Walked outside and the wife says "what's under your truck?"

Going back in to order a water pump.

Here are some deal savings online coupons from advance auto. You can order online and pick up in local store.

http://m.retailmenot.com/view/advanceautoparts.com

 

[retorq]

Finally got it in ... gonna hook everything up tomorrow, may have to fix a couple wires, the VSS wires are down to bare metal. :/

Stupid rear end pinion seal is leaky too.

 

[slipping]

Here are some deal savings online coupons from advance auto. You can order online and pick up in local store.

http://m.retailmenot.com/view/advanceautoparts.com

Thank you good sir! I looked and dont have any advance autos near me.

Finally got it in ... gonna hook everything up tomorrow, may have to fix a couple wires, the VSS wires are down to bare metal. :/

Stupid rear end pinion seal is leaky too.

That looks like fun! (Not being a smart ass - I want to learn)

 

[Gzes]

Damn bolt is still in. I redneck welded nuts on the bolt but no good it keeps on poppin off. I have to thin rod and cant control the arc because im running car batteries and not a real welder lol. Crud has come loose tho so hopefully it cones out tomorrow

 

[stereodesigner]

I washed her up, went to check out some all terrains for it...
Now I'm. Trying to figure blackbearperformance or pcm4less


Sent from my DROID X2 using Tapatalk 2

 

[qukon 95]

ready for winter

i replaced my LTW DELCO wires and the delco plugs. the
old plugs gap was .059 lol i should have better pick up
now.

 

[knoslf]

Just got done ordering new plugs, wires, cap, rotor and k&n this morn. Walked outside and the wife says "what's under your truck?"

Going back in to order a water pump.

Nice lookin truck! I think I'll take my runnin boards off too, gives the impression that it sits higher, well my suspension is all stock though...

 

[slipping]

Nice lookin truck! I think I'll take my runnin boards off too, gives the impression that it sits higher, well my suspension is all stock though...

Thanks dawg. I just don't like seeing that frame. One day it will lay on the ground, but until then ...

 

[retorq]

That looks like fun! (Not being a smart ass - I want to learn)

Not that hard, just nuts, bolts and a couple wires.

 

[SPLmonster13]

Tried out plastidip for the first time

 

[retorq]

Drove it to work. \m/

 

[Gzes]

test fitted my guard and am stuck on keeping it on frame or lift it up with the brackets and loose strength

 

[slipping]

test fitted my guard and am stuck on keeping it on frame or lift it up with the brackets and loose strength

If you left on frame could you Fab a filler for in between?

 

[clownracer]

got some 16.5" rims im doing 37's my 35s are officially fs

 

[Gzes]

If you left on frame could you Fab a filler for in between?

Yea thats what i thought. I had it that way in my ram but idk i might just do it over at the trade school n weld some more diamond plate on there to fill it