Show off your 2015+ leveled Tahoes and Yukons!

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

MikeK1981

Member
Joined
Jul 10, 2021
Posts
32
Reaction score
21
I haven’t crawled under to look, is it one piece with the front bumper? I was hoping it was separate and attached somehow and could be removed.
They can be removed but my understanding is that it's kind of a pain to do. Also it kind of leaves an unfinished look imo. I left about 2.5-3 inches of material if i remember correctly. The PPV ones I think are more like 1-2 inches. You can click that image and zoom in. Hard to tell at the angle but cutting it right at the natural 'belly' shape of the plastic piece, leaves it just a little higher than the side steps when looking at it from the side. Looks much better but at the same time most people wouldn't know it isn't stock, and gained me about 4.5 inches of ground clearance. Plus I figured that maybe it doesn't totally negate the aerodynamic effects that it's supposed to help with. You could always trim more.
 

Attachments

  • 20220810_145132.jpg
    20220810_145132.jpg
    309.4 KB · Views: 60
  • 20220810_145140.jpg
    20220810_145140.jpg
    391.5 KB · Views: 60
Last edited:

12lbs boost

TYF Newbie
Joined
Dec 11, 2022
Posts
24
Reaction score
47
Finished 1st round of mods. 1.5 suspension maxx level and 2022 at4 take offs with 33s. These wheel wells have way more room in the front then my old NNBS. Eventually going to throw on my 2 5 / 1 " ccm kit and go a bit bigger on tires. Thanks to all on this forum for great info. 20230213_181346.jpg20230212_105348.jpg20230212_171252.jpg
 

Bvalday

TYF Newbie
Joined
Mar 8, 2023
Posts
1
Reaction score
0
After several months of looking at pictures and going back and forth on what level kit to install on my Wife's 2020 Suburban Premier RST, I've decided to go with the Suspension Maxx 2.5/1.5" level with the rear 1.5" shock extensions. I'm quite pleased with the results!
Great looking Rig! Is that a rhino rack pioneer platform on top?
 

cardershack

Member
Joined
Oct 26, 2022
Posts
31
Reaction score
9
Did you trim the front air dam using a saw of some sort or were you able to remove it somehow?
I used an angle grinder w/ a cut off wheel to cut mine off. I taped my line and tried to follow it the best I could. I think an oscillating tool would be better than a grinder with a cut off wheel but it did the job. I definitely went quick and didn’t do the cleanest job but sanded any chunks of melted plastic off and you can only see the imperfection if you get on the ground and look under the bumper so don’t worry too much about not doing it perfectly. I’m glad I did it but may use a different tool if I had to do it again.
 

Attachments

  • A1CA4D77-AA96-455E-9814-106B07C011E8.jpeg
    A1CA4D77-AA96-455E-9814-106B07C011E8.jpeg
    569.4 KB · Views: 24
  • B083DFA0-4BE1-49AE-9393-31E697090C26.jpeg
    B083DFA0-4BE1-49AE-9393-31E697090C26.jpeg
    581.9 KB · Views: 23

12lbs boost

TYF Newbie
Joined
Dec 11, 2022
Posts
24
Reaction score
47

Attachments

  • 20230311_122926.jpg
    20230311_122926.jpg
    604.7 KB · Views: 34
  • 20230311_122940.jpg
    20230311_122940.jpg
    574.6 KB · Views: 38

Jisnis

Member
Joined
Apr 11, 2015
Posts
34
Reaction score
18
I’ve gone through the entire thread and didn’t see anyone run a negative offset. I’m looking to run a 17x8.5 -10/-12 wheel with hopefully 35s. I wanted to see if there would be too much poke with a -10/-12 offset. The wheel I’m looking at is the SCS Ray10 wheel and unfortunately they don’t make the wheel in a 0 or positive offset. Anyone have pictures of their negative offset?
 
Last edited:

olyelr

Full Access Member
Joined
Mar 19, 2011
Posts
1,626
Reaction score
759
Location
Elk Rapids, MI
I’ve gone through the entire thread and didn’t see anyone run a negative offset. I’m looking to run a 17x8.5 -10/-12 wheel with hopefully 35s. I wanted to see if there would be too much poke with a -10/-12 offset. The wheel I’m looking at is the SCS Ray10 wheel and unfortunately they don’t make the wheel in a 0 or positive offset. Anyone have pictures of their negative offset?
Go to the gallery at customoffsets and narrow down your search to what you are looking for. Im sure there will be zillions of pics available
 
Top