2009 Suburban Build Thread (SOLD)

[THE YETI]

[emoji106]used the Patented Yeti method eh? LOL

 

[devious1]

looking forward to seeing the pics.

 

[Goodinblack]

Just bought another one of these.

The old Eagle Eyes replica ended up on the black Yukon XL.

I honestly would never buy a another EE replica. Sumbich started to warp.

 

[devious1]

how was the paint underneath the door moldings? everything turn out okay?

 

[felixgun]

Just bought another one of these.

The old Eagle Eyes replica ended up on the black Yukon XL.

I honestly would never buy a another EE replica. Sumbich started to warp.

Yeaaa oem is always better :/

 

[Goodinblack]

how was the paint underneath the door moldings? everything turn out okay?

Yes Sir.

Washed, clayed, and polished the lower half last night. Also rewaxed the entire right side with 845 as well.
I will post pictures soon.

---------- Post added at 01:38 PM ---------- Previous post was at 01:14 PM ----------

Yeaaa oem is always better :/

Yep

Bought it from the eBay seller

 

[Goodinblack]

looking forward to seeing the pics.

 

[Ben]

Time for some 2010+ trim

 

[07Burb]

What lift kit is that?

 

[Joew311]

GIB, I couldn't stop until I went through every page of your build thread! It has got me thinking about documenting my mods a little better! Thanks for all of the information. Your burb looks amazing, keep up the great work and posts!

 

[Big Buttons]

Lol just don't take 8 months for some lights

 

[Goodinblack]

GIB, I couldn't stop until I went through every page of your build thread! It has got me thinking about documenting my mods a little better! Thanks for all of the information. Your burb looks amazing, keep up the great work and posts!

Thank you Sir



---------- Post added at 10:49 AM ---------- Previous post was at 10:48 AM ----------

Lol just don't take 8 months for some lights

LOL

 

[MudnRox]

Just read your whole build thread. Very nicely done. Very nice looking rig. I got a few good ideas I'm thinking of trying out. Thanks for the well documented thread.

 

[Goodinblack]

Just read your whole build thread. Very nicely done. Very nice looking rig. I got a few good ideas I'm thinking of trying out. Thanks for the well documented thread.

Thank you good Sir

 

[Goodinblack]

So finally broke down and bought a CatchCans.com can.

Bought a "clear aluminum" one.

Originally was going to go the oil/water separator route from Sears.... but ended up using that on my air compressor.....

 

[THE YETI]

It's 2015. You can start on a new project now.

 

[Goodinblack]

It's 2015. You can start on a new project now.

Eventually will.

 

[Joew311]

So finally broke down and bought a CatchCans.com can.

Bought a "clear aluminum" one.

Originally was going to go the oil/water separator route from Sears.... but ended up using that on my air compressor.....

Did you install this yet? I don't know if you will notice much since yours is gray, but I'm curious if this reduces the black marks on the rear panel above the SLP tip from exhaust.

 

[pwtr02ss]

Did you install your interior door handles yet? I bought some about 6 months ago but haven't got around to doing them. Was wondering how bad it was.

 

[07Burb]

Did you install your interior door handles yet? I bought some about 6 months ago but haven't got around to doing them. Was wondering how bad it was.

I replaced my driver's interior door handle a few weeks back and it was easy. If you've taken your door panel off before and your familiar with how all that works it should be a 15-20 minute job tops where 2 minutes of that is the handle part LOL