What did you do to your NNBS GMT900 Tahoe/Yukon Today?

[cmatt]

View attachment 258115

Thanks. I saw that and almost pulled it, but didn’t. I went out and did. Looks to be the ticket.

I actually did look in the OTC book that covers up to 2013 MY vehicles and the 2012 Suburban & Tahoes aren’t listed. I then checked the service manual and it just states to disable the relay. Couldn’t find the procedure on how to do so. I’m sure that was operator error.


Sent from my iPhone using Tapatalk

 

[George B]

what kind of pads are you using?

Raybestos Element3. They work pretty well and provide good stopping. They just want to squeal occasionally.

 

[Doubeleive]

Raybestos Element3. They work pretty well and provide good stopping. They just want to squeal occasionally.

looks like those are a combination of ceramic and semi metallic that is why they squeak, the metallic part causes it. If you go all ceramic they will be dead silent

 

[George B]

looks like those are a combination of ceramic and semi metallic that is why they squeak, the metallic part causes it. If you go all ceramic they will be dead silent

Yup. I have had many sets of semi metallic pads over the years and like the way they stop. This things brakes are fantastic with these pads so I will work through it. Picked up some disc brake quiet spray and gave them a coat. The one that was squeaky got scuffed with 180 grit flat on the bench. Good for now.

 

[08z71bgm]

Semi creates a ton of dust but stops the best. Ceramic is quiet and dust free for the most part but don’t stop nearly as good.

 

[Sam Harris]

Semi creates a ton of dust but stops the best. Ceramic is quiet and dust free for the most part but don’t stop nearly as good.

I’ve been really happy with the Powerstop carbon ceramic pads.

 

[08z71bgm]

I’ve been really happy with the Powerstop carbon ceramic pads.

I would never use them again even if I got them for free. Used the z26 and z36 before on many different applications. The nbs and other cars. Power stop won’t be getting anymore of my money. EBC is a much better brand.

 

[George B]

I bought the pads and coated rotors from Raybestos because I was after the corrosion resistance of the coating. Prior to this it was some form of Wagner premium stuff. Whatever their flavor was at the time. That said nothing helped on my NBS. That thing had the worst brakes!

 

[Doubeleive]

The new copper free pads from autozone seem to work really well I have no complaints

 

[08z71bgm]

I bought the pads and coated rotors from Raybestos because I was after the corrosion resistance of the coating. Prior to this it was some form of Wagner premium stuff. Whatever their flavor was at the time. That said nothing helped on my NBS. That thing had the worst brakes!

No way. I replaced my calipers and put oem pads and rotors the gray one. It stopped amazing. That ***** cross drilled and slotted crap from power stop was a waste of money. Even with that zinc coating they still rusted.

 

[Rocket Man]

Wawa and Qik chek.

You guys have a BucEes? Can’t walk into that place without spending $50 not counting the gas!!!

Nope, never even heard of that one.

I’ve never heard of ANY of these. Must be an East of the Rockies thing.

 

[Drok]

I’ve never heard of ANY of these. Must be an East of the Rockies thing.

not to far east ive never heard of them either haha

 

[Drok]

No way. I replaced my calipers and put oem pads and rotors the gray one. It stopped amazing. That ***** cross drilled and slotted crap from power stop was a waste of money. Even with that zinc coating they still rusted.

yup i have just slotted ones (not ps) and they rusted in the slots and when i hit the brakes it humms and has a lights vibration.

 

[massivespl]

got the floor and three doors done today. Going to start the last door and roof tomorrow. Used about 108sq ft so far

 

[5strmtrp]

Pulled the headlights out, total bs that you have to loosen up the bumper to remove. Trying to figure out the wiring mess under the center stack disconnected a few extra power leads in various spots in the truck. Hell I posted it in the police section. She needs a good interior clean.

 

[mikeyss]

View attachment 258147 View attachment 258146 View attachment 258148
got the floor and three doors done today. Going to start the last door and roof tomorrow. Used about 108sq ft so far

Don't forget to get the top of those wheel wells and maybe a quarter of the way up the side wall under the window. That quarter panel is hollow inside with no way to fill it, at least block off the squares to keep the hollow tire noise out. I have also put more deadening on the floor where the 3rd row is, and it makes a big difference.

 

[massivespl]

Don't forget to get the top of those wheel wells and maybe a quarter of the way up the side wall under the window. That quarter panel is hollow inside with no way to fill it, at least block off the squares to keep the hollow tire noise out. I have also put more deadening on the floor where the 3rd row is, and it makes a big difference.

this vehicle is getting a b pillar wall with six sundown xv2 12s on two vital power 700.1s. All holes will be filled with deadener and spray foam. I got some wood strips for the roof along with deadener. I got a few friends with some 160db+ vehicles

 

[07Burb]

this vehicle is getting a b pillar wall with six sundown xv2 12s on two vital power 700.1s. All holes will be filled with deadener and spray foam. I got some wood strips for the roof along with deadener. I got a few friends with some 160db+ vehicles

That thing gonna be a heavy sumbish! Lol

 

[CaptainAmerica1]

I’ve never heard of ANY of these. Must be an East of the Rockies thing.

I’m in Dallas. QT on every corner, BucEes is newer and bigger...

 

[Chert_Detective]

I know everyone likes dirty/clean before and afters. Took my time, and a few beers, on doing the valley cover gasket and oil pressure sensor yesterday and today. All back together and running now but I did remember snap an after picture.