2001 GMC Yukon XL (Aka Beast)

[Fless]

What diagnostic trouble code(s) are lighting the lights?

 

[makintoshnex]

I ordered another harness. It may be that my GMC is using same harness as for the left and right side. I tried to switch them they fit. The tiny thumb on right harness is same as for the left one. I found cheap one new from 2000 GMC Sierra 2500 for 35 bucks. We'll see. So far left turn signal doesn't work. I swapped old taillight back. I tried to fit the new wing from Escalade. Did some custom brackets. Need to wire it.

 

[makintoshnex]

The biggest issue is that I'm doing everything on a street. I have no garage or driveway. Those holes for spoiler I will fill in with window seal . I can't weld plastic, got no tools for that.

 

[Bigburb3500]

The biggest issue is that I'm doing everything on a street. I have no garage or driveway. Those holes for spoiler I will fill in with window seal . I can't weld plastic, got no tools for that.

I feel you on the street work. Did all my work in a parking lot or at the local AutoZone.

 

[makintoshnex]

Alright fellas. I did wherever I could. Now I need you assistance. I need to wire the lights. I have no problem with reverse light. That one I did. I can't do anything to brake light, running light, turn signals. Actually I can. But they keep working, especially running light even when engine is off and ignition is off too. I need somehow bring 12 volts to th back that will automatically shut down when vehicle is on alarm. I bought these taillight, they have same harness as mine. So no problem. Just one thing, power. On order to activate power in spoiler I need 12 v constant.

 

[makintoshnex]

Ok. So that's what I ayeballed. I wired it to the numberplate light. And I replaced factory ones into these. So far not bad. This is simply running light. It's COB . Also I wired reverse light in pillars, unfortunately I didn't manage to obtain same light for them. I had in a household proven with time old LED, I used them at work. So I had to go with that. And also my wife gave an ultimatum, so either spoiler and those pillars are out or she will get rid of a truck. I live in apartment it's small 1 bedroom with 2 kids, you know. I had to take it. And by the way I haven't installed spoiler permanently, it's holding on one screw and 2 makeshift brackets.

 

[makintoshnex]

I played I bit with my fuse box and after abs light flickered agaIin got these codes

 

[makintoshnex]

I finally fixed exhaust leak, now it's not farting, it's decent sound, before I thought about changing the resonator, but now I think I will keep it stock. It's loud enough

 

[makintoshnex]

Alright, good news and bad news. Good news that I finally finished wiring d pillar lights and 2007 Escalade spoiler light . Bas thing is that I couldn't extract 2 screws from ABS control module. They are seized and torx head was rusted out. So unfortunately I will have to replace the whole thing. But I don't know if it makes any sense. We don't have junk yards here in Brooklyn. And I don't know where to go and what to do. More over, someone was at ABS module. I used mirror to check it out, it's dorman, not original. Plus someone used zip ties to hold connectors in place. So I don't think it mame any sense to play with soldering. Unfortunately the job with a part will be expensive, close to $900 . Now I face another thing, should I fix it, though nobody reimbursed me a thing, or should I sell the truck?

 

[Bigburb3500]

Alright, good news and bad news. Good news that I finally finished wiring d pillar lights and 2007 Escalade spoiler light . Bas thing is that I couldn't extract 2 screws from ABS control module. They are seized and torx head was rusted out. So unfortunately I will have to replace the whole thing. But I don't know if it makes any sense. We don't have junk yards here in Brooklyn. And I don't know where to go and what to do. More over, someone was at ABS module. I used mirror to check it out, it's dorman, not original. Plus someone used zip ties to hold connectors in place. So I don't think it mame any sense to play with soldering. Unfortunately the job with a part will be expensive, close to $900 . Now I face another thing, should I fix it, though nobody reimbursed me a thing, or should I sell the truck?

I think you should keep at it. With your current cost in the truck it is still FAR cheaper than any other work truck.
I had similar issues as you did with mine as I had to undo so many janky fixes. If I am following your thread correctly, you are on the final stretch as you fixed the brake lights and just have the ABS lights now?
If so you are basically there. These are easy to maintain once they are fully operational and given your price point, I would not be concerned until your bills start totaling $4-5k. Your truck in full running condition is a $6-8k truck (imo).