What did you do to your OBS GMT400 Tahoe/Yukon Today?

[chaingun427]

Hmm where can I get those from? Never had an issue with Felpro myself but that's almost always been stock manifolds too

 

[jerryjoe28]

Do yourself a favor and get the compressed graphite ones, I originally put fel-pro gaskets when I did my headers and they never sealed properly and totally gave up after 3000 miles. The compressed graphite gaskets are much nicer.

cent frum a smaert fone

yea mine came with graphite gaskets and said DO NOT use anything else

 

[noJeepshere]

Hmm where can I get those from? Never had an issue with Felpro myself but that's almost always been stock manifolds too

My mechanic got them from his supplier so I don't really know. A good hot rod shop would have them for sure.

cent frum a smaert fone

 

[rabbiporkchop]

Dropped the fuel tank to replace fuel pump.

 

[mattss90]

ive spent a few hours looking at how to upgrade the towing/weight capacities from 6200 to hopefully the 8000+ range(i know the motor can but not the axle), bigger and better rear axle for towing and maybe looking into getting a 4L80 tranny instead of regearing, putting a shift kit, and a badass tranny cooler on my 4L60.

 

[noJeepshere]

6 lug 14 bolt semi-float axle with 4.10 gears and disc brakes, helper springs or air bags, swap your trans for a 4l70e (the same low gears as the '60e but almost as strong as the '80e) new master cylinder for the discs. That will get you your load capacity.

cent frum a smaert fone

 

[chaingun427]

6 lug 14 bolt semi-float axle with 4.10 gears and disc brakes, helper springs or air bags, swap your trans for a 4l70e (the same low gears as the '60e but almost as strong as the '80e) new master cylinder for the discs. That will get you your load capacity.

cent frum a smaert fone

Hydroboost is also a good upgrade if you dont' want to do the disc conversion.

--

I got the floor cut out of Rollie to reveal this big beautiful bastard
NV4500 and np241

 

[bigal11419]

Finally took apart the denali console I bought to start cleaning it up and refinishing it.

 

[qukon 95]

Are you going to use that sub?

 

[bigal11419]

Still undecided on the sub. Definitely not using the amp and cd changer. Still haven't finalized what I am adding to it.

 

[chaingun427]

Any good consoles that would accommodate a manual transmission?

 

[_Dylan_]

Put some wipers on it lol. Might change the oil this weekend.

 

[jerryjoe28]

got the 4.56s and trutrac in! man what a difference

 

[Goodinblack]

April Truck of the MONTH contest

24s or MORE

http://tahoeyukonforum.com/forum/showthread.php?t=71365

 

[chaingun427]

Got the old slushbox out yesterday, and dropped the lower dash and steering column in preparation of cutting some holes! going to be cutting out and installing the clutch master, and tcase shifter tomorrow, and cutting the hole for the manual shifter.

With any luck this weekend I can pull the motor and trans from Rollie and go straight into the hoe with it.

 

[bigal11419]

Ordered all new steering linkage parts, new tail lights, new belt, new idler and tensioner pulleys, and a steering damper. Hopefully I get some nice weather when everything shows up.

 

[chaingun427]

Got the drive train pulled from rollie finally time to get it cleaned up and into the hoe

 

[95escahoe]

Picked up these frame bumper brackets from my buddy today he powder coated them, came out mint

Here they are before

 

[qukon 95]

That sub is 1.4 ohms so you will need a class d amp that's STABLE @ 1ohm. I did the mtx class d 350 rms@ 1ohms for mine since there's no power rating on the sub this is plenty of power for sub to me.
I got theLP filter at 100 hz this little sub does the job
:worship

 

[Y2KpewterZ]

Refurbished this Denali console