What did you do to your OBS GMT400 Tahoe/Yukon Today?

[BattelWagun]

I found a bumper from a florida truck on craigslist yesterday for $100, talked him down to $80. It's in awesome condition, hardly a spot on it. Now all I need is the bracket kit, and probably a plasma cutter to get the old one off...

Currently chasing down a bull bar off an F-250 with a pair of Hella 500's on it. He's asking $250, I'm gonna see if I can get him to $200

 

[vtx1800sba]

Chad, FlowMaster does make one for a 2 door, but not in stainless. Just aluminized steel. Where I live road salt and gravel roads will eat the hell out of an aluminized system.

 

[ch4d]

Chad, FlowMaster does make one for a 2 door, but not in stainless. Just aluminized steel. Where I live road salt and gravel roads will eat the hell out of an aluminized system.

oh okay..

 

[jdpber]

 

[SunlitComet]

I am such a nobody in this world I am not even worthy enough to stare at the pic even though I tried.

 

[LI99HOE]

I am such a nobody in this world I am not even worthy enough to stare at the pic even though I tried.

Never......

.....and ......DAMN that's a big bird!!!

 

[AlanHurd54]

yeah the bird is what u noticed not the 2 huge turkey ******* above it

 

[SunlitComet]

Physical install of flexalite 280 efans complete. Will do wiring tomorrow morning.

 

[AtomicHoe094]

nice.. looks good Sun.. have fun! and youll have to unmount them again to complete the wiring

 

[SunlitComet]

Just wiring on the outside needs to be done. Already wired the motors to controller before mounting.

 

[AtomicHoe094]

good call. tell me where you run the one wire for ignition

 

[SunlitComet]

on the 96 Vortecs there is a fuse that powers the ignition module, coil and two sensors with igntion on. So I will tap into that. At least until I build an "engine running" circuit perhaps.

 

[AtomicHoe094]

hmm. I need a good place for mine, i ran mine to something under the dash in the meantime and it works but i need a better place

 

[SunlitComet]

How about ecm 1 under the hood?

 

[LI99HOE]

yeah the bird is what u noticed not the 2 huge turkey ******* above it

Who said I didn't notice 'em???? Lmao.....

 

[qukon 95]

getting closer to finishing my new A pillar spkr pods sinse i swapped my dash.

my old pass side pod won't work with this dash.

 

[retorq]

Finished up the custom shift boot for the Megashifter ...

 

[LI99HOE]

That looks freakin' awesome !!!

 

[rushr]

Installed new interior driver door handle...I was getting tired of rolling down the window to open the door...lol I also started to clean the leather seats. The driver seat is no longer dark, dingy, smooth looking leather...although they will eventually have to be replaced or recovered. The driver seat has a big tear on the side from sliding in/out.

 

[LI99HOE]

Installed new interior driver door handle...I was getting tired of rolling down the window to open the door...lol I also started to clean the leather seats. The driver seat is no longer dark, dingy, smooth looking leather...although they will eventually have to be replaced or recovered. The driver seat has a big tear on the side from sliding in/out.

I had the same damn thing...
I found a leather repair kit on Ebay that matched my leather seat cover perfectly....was cheap.... and best of all..... took care of the rip/missing piece in my drivers seat.
Might be a cheap/easy fix for ya'.