Coolant leak at bellhousing after brand new GM Crate Motor install - SOLVED

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

hank89

TYF Newbie
Joined
Aug 10, 2021
Posts
10
Reaction score
12
So I just put in a new gm crate motor this weekend in my 99 tahoe. I was so excited when I got everything back together, being this was the first time I pulled a motor and put a new one in. And it started right up!

And then I noticed a day later that it was losing coolant and there was a drip from the transmission bell housing.

I cannot tell you how disappointing this is after spending about 8k between the new crate motor and all the new parts I added. I put in the felpro gaskets with new bolts w/ threadlocker...and I used the black rtv in the felpro kit for the chinawalls.

Since having the tahoe, I had a shop put in gaskets at 100k miles; then I replaced them again with felpros at 175k miles...and then I replaced the engine at 253k miles. I cannot tell you how many hundreds of dollars I spent on antifreeze for the first motor.

Now my new engine is already leaking coolant. The lower intake on the 5.7 is a P.O.S. I cannot believe someone has not made an intake that actually works and doesn't leak.

I am beyond pissed off.

So for those of you thinking about replacing your 5.7 with another.... If I had to do it again, i would of spent a few more dollars and got a brand new GM engine with completely new fuel injection system. Maybe an LS or one of the ramjets.
 

east302

Full Access Member
Joined
Dec 21, 2016
Posts
1,555
Reaction score
1,379
Location
Mississippi
Adding to the above, the knock sensor could (in theory) leak bad enough for air to blow coolant back that far. I did have a bad hose at the intake quick connect that did a slow leak that drifted down the intake/valve cover valley back toward the starter.

But, yeah, that sucks. The reinforced Felpro gaskets tend to last longer than their cheaper non-reinforced ones, but both should make it a hell of a lot longer than a day.

Did you put RTV on both the top and bottom of the little gasket tab where it meets the china wall? The RTV was allowed to cure? Usually, by the time I’ve gotten everything back together it’s had plenty of time to set.

AD3CE52D-FFF6-48D1-9E41-E5C212142FCA.jpeg

EA72086B-4293-44BF-AD26-267DD8480979.jpeg
 

WHYTNOYZ

TYF Newbie
Joined
Sep 20, 2021
Posts
5
Reaction score
4
I have them on both front and rear drilled/slotted and it's been about a year and some change without anybissues I can think of. Actually I bought them blacked out and during the break in process they turned to the standard metallic color which was a bit of a number since my rides all blacked out. Pads are decent as well.
 

OR VietVet

Multnomah Falls
Supporting Member
Military
Joined
Oct 8, 2014
Posts
19,067
Reaction score
31,162
Location
Willamette Valley
Coolant drip on the outside and dripping off the bell housing or coolant dripping from inside the bell housing? Could be any of the above or a welch/freeze plug at back of block if from inside the bell housing.
 
OP
OP
H

hank89

TYF Newbie
Joined
Aug 10, 2021
Posts
10
Reaction score
12
Have you checked your heater hoses near the firewall?

I agree, the lower intake design on that gen one motor is a PITA. I had to replace one on my sons ‘97 K1500 last January when it was 10° outside.
I don't believe I have heater hoses near the firewall. I replaced the 2 heater hoses (3/4" w/ plastic quick connect into the lower intake and the 5/8" at the water pump). I have a tahoe which doesn't have the rear heater like the suburban.
 
OP
OP
H

hank89

TYF Newbie
Joined
Aug 10, 2021
Posts
10
Reaction score
12
Adding to the above, the knock sensor could (in theory) leak bad enough for air to blow coolant back that far. I did have a bad hose at the intake quick connect that did a slow leak that drifted down the intake/valve cover valley back toward the starter.

But, yeah, that sucks. The reinforced Felpro gaskets tend to last longer than their cheaper non-reinforced ones, but both should make it a hell of a lot longer than a day.

Did you put RTV on both the top and bottom of the little gasket tab where it meets the china wall? The RTV was allowed to cure? Usually, by the time I’ve gotten everything back together it’s had plenty of time to set.

View attachment 386829

View attachment 386830
Thanks east302...I will check the knock sensor...I put a new one on. Yes...I did put RTV on the top and bottom of the gasket tab/return at the china wall.

I used the rtv that came with the MIK98000T kit. There wasn't much in the kit...and I did the front wall first, then when i did the back, i'm wondering if i didn't put enough on. I did give it time to set where it wasn't sticking.

I'm going to get a camera and see if I can locate exactly where it is coming from.

Thank you for all the info!!!
 
OP
OP
H

hank89

TYF Newbie
Joined
Aug 10, 2021
Posts
10
Reaction score
12
Coolant drip on the outside and dripping off the bell housing or coolant dripping from inside the bell housing? Could be any of the above or a welch/freeze plug at back of block if from inside the bell housing.
Thanks for the reply. Will look into this further. I hope it is not the freeze plug(s). this is a brand-new gm crate motor.
 

east302

Full Access Member
Joined
Dec 21, 2016
Posts
1,555
Reaction score
1,379
Location
Mississippi
Thanks east302...I will check the knock sensor...I put a new one on. Yes...I did put RTV on the top and bottom of the gasket tab/return at the china wall.

I used the rtv that came with the MIK98000T kit. There wasn't much in the kit...and I did the front wall first, then when i did the back, i'm wondering if i didn't put enough on. I did give it time to set where it wasn't sticking.

I'm going to get a camera and see if I can locate exactly where it is coming from.

Thank you for all the info!!!

If that RTV at the wall was somehow “not right” enough to send coolant down the back of the block, then I’d think that you would see coolant in the oil fairly quickly. It wouldn’t hurt to drain it and see, but an external leak at a hose or something just sounds more likely.

A coolant pressure test may be in order.

Regarding the heater hoses, that poster was referring to the two lines going through the firewall under the a/c accumulator.
 

exp500

Full Access Member
Joined
May 14, 2017
Posts
1,780
Reaction score
1,609
One of my work trucks had a small unable to locate coolant leak. Took about 60 days of watching until either the leak got bigger or sunight was perfect- was leaking at plastic tees for rear heat and squirting a tiny stream towards exhaust manifold/spark plug. Leak was about 1 quart a week. A quick wrap in paper towel verified exact location.
 

Forum statistics

Threads
128,781
Posts
1,805,301
Members
91,760
Latest member
MyCleftNut

Latest posts

Top