What did you do to your NNBS GMT900 Tahoe/Yukon Today?

[Geotrash]

How far will one bottle take you?

I don't know - I haven't put it in the gas tank.

Seriously though, I'm still working through my first bottle and have maybe another 2-3 cars' worth of solution left. It only requires a light mist on the finish, which you then spread around with a microfiber towel to get an even film. After that, just buff it with a 2nd, clean and dry microfiber towel to get the high luster. You can do a whole XL Denali in 10 minutes.

 

[gooffeyguy]

Gave both Denali's and our LR2 a fresh ceramic spray wax treatment with Griot's Garage 3-in-1 Ceramic Spray Wax. Super impressed with this stuff. I've been using it every 2-3 months for the past year and the water still beads and grime doesn't stick right up until the next treatment. I didn't take pictures of the Denali's but did take some of the finish on the LR2. Keep in mind that it's 14 years old with 230K, and has been parked outside for the past 5 years.

View attachment 377811

https://www.amazon.com/Griots-Garage-10978-Ceramic-22oz/dp/B084F4DC92/ref=asc_df_B084F4DC92/?tag=hyprod-20&linkCode=df0&hvadid=416678661258&hvpos=&hvnetw=g&hvrand=13905971060249129316&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=2840&hvtargid=pla-886955401161&psc=1&tag=&ref=&adgrpid=92859401406&hvpone=&hvptwo=&hvadid=416678661258&hvpos=&hvnetw=g&hvrand=13905971060249129316&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=2840&hvtargid=pla-886955401161

Says it's Safe for plastics.... Should use it on the dash to help keep it from cracking

 

[CaptainAmerica1]

Gave both Denali's and our LR2 a fresh ceramic spray wax treatment with Griot's Garage 3-in-1 Ceramic Spray Wax. Super impressed with this stuff. I've been using it every 2-3 months for the past year and the water still beads and grime doesn't stick right up until the next treatment. I didn't take pictures of the Denali's but did take some of the finish on the LR2. Keep in mind that it's 14 years old with 230K, and has been parked outside for the past 5 years.

View attachment 377811

https://www.amazon.com/Griots-Garage-10978-Ceramic-22oz/dp/B084F4DC92/ref=asc_df_B084F4DC92/?tag=hyprod-20&linkCode=df0&hvadid=416678661258&hvpos=&hvnetw=g&hvrand=13905971060249129316&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=2840&hvtargid=pla-886955401161&psc=1&tag=&ref=&adgrpid=92859401406&hvpone=&hvptwo=&hvadid=416678661258&hvpos=&hvnetw=g&hvrand=13905971060249129316&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=2840&hvtargid=pla-886955401161

Sounds like a 2am infomercial

 

[gooffeyguy]

I did ZERO to my vehicles today. My thighs are killing me today after working on the front suspension yesterday. Must've done too much kneeling. Getting old sucks

 

[Tonyrodz]

I did ZERO to my vehicles today. My thighs are killing me today after working on the front suspension yesterday. Must've done too much kneeling. Getting old sucks

 

[Tonyrodz]

 

[swathdiver]

I did ZERO to my vehicles today. My thighs are killing me today after working on the front suspension yesterday. Must've done too much kneeling. Getting old sucks

 

[gooffeyguy]

View attachment 377859

I have one of those, but it would've been too high and I would've been bent way over.

I sat on the ground most of the time but after disconnecting the upper ball joint and tie rod I was squatting or on one knee using my leg to help hold the spindle/hub/brake kind of in place while strong arming the prybar and placing the spacers and aligning the bolts all at the same time.

It's not my entire thigh that hurts, just right above the knee and to the inside. It's weird, usually it's my lower back that would be sore for a day or so, not my legs.

 

[89Suburban]

View attachment 377859

Using mine today DIY alignment

 

[89Suburban]

Got a new tool

 

[89Suburban]

 

[89Suburban]

Brake pad check while I’m at it.

 

[89Suburban]

So I set the level to 0 on the rear wheel and here is the front reading. Just a tad over -1*.

 

[89Suburban]

Using the 4 bottles of washer fluid with the string lines on each side squared the lines up to the rear tires then adjusted the front toe in on each front tire to 1/16”.

 

[89Suburban]

Here is the right rear 0’d out and the front measurement. Little too much here. But my driveway isn’t perfectly flat either. I’ll double check those at work on the flat finished warehouse floor to compare later.

 

[PG01]

I did ZERO to my vehicles today. My thighs are killing me today after working on the front suspension yesterday. Must've done

I did ZERO to my vehicles today. My thighs are killing me today after working on the front suspension yesterday. Must've done too much kneeling. Getting old sucks

Lol, what are you 12? Wait till you get to be @Tonyrodz age!!!! Lol… kidding Tony

 

[gooffeyguy]

Lol, what are you 12? Wait till you get to be @Tonyrodz age!!!! Lol… kidding Tony

12, lol. I'm in my 50s

 

[Tonyrodz]

Lol, what are you 12? Wait till you get to be @Tonyrodz age!!!! Lol… kidding Tony

Wish I was 12!

 

[gooffeyguy]

Here is the right rear 0’d out and the front measurement. Little too much here. But my driveway isn’t perfectly flat either. I’ll double check those at work on the flat finished warehouse floor to compare later.



View attachment 377890View attachment 377891View attachment 377892

That all seems easy enough, but very time consuming. I'm just gonna drop mine off at the shop 3 blocks away on Tuesday and pay them the $90 to do it

 

[89Suburban]

That all seems easy enough, but very time consuming. I'm just gonna drop mine off at the shop 3 blocks away on Tuesday and pay them the $90 to do it

It's a challenge, a lot of work and a learning opportunity.