What did you do to your NNBS GMT900 Tahoe/Yukon Today?

[swathdiver]

Duplicate.

 

[Rocket Man]

Yeah but you know they're more better!

Yessir, and required for the cam I just installed.

 

[iamdub]

Oh it’s been a bit of a PITA. I’ve got an aftermarket head unit, and remote start. So we figured out those both have to be 100% disconnected, so I have to pull fuses in the dash every time I do anything w/ the AutoCal.
After I was finally able to provide a data log, he sent a tune back right away, but with additional information that my MAF was pretty well toast. So I’m sitting waiting for it to arrive tomorrow.

On that note, I need a good plan for the replacement. I was planning to clear any faults with the Tech2 after replacement, and then hopefully start right up, but I know enough to expect it won’t go so easy like that. [emoji6]

Maybe it's you and Mark tying them up.

I have an aftermarket HU as well so I'll keep that in mind when I get involved with it. Thanks for mentioning that.

I don't see the new MAF and clearing the codes causing any problems unless the new tune needs completed drive cycles/readiness monitors.

 

[Rocket Man]

Maybe it's you and Mark tying them up.

I have an aftermarket HU as well so I'll keep that in mind when I get involved with it. Thanks for mentioning that.

I don't see the new MAF and clearing the codes causing any problems unless the new tune needs completed drive cycles/readiness monitors.

Yeah I’m still waiting on my tune for the cam. Roger Vinci said I can start it up and do the initial run- in but it will run raggedy and throw codes until the tune is loaded. I sent in my request last Friday so I’m hoping to hear back soon. @BlackBearPerf are you listening? I sent them a PM too.

 

[George B]

Well, I need to slow down a bit.

While I was cleaning the wheels up a bit I noticed one wheel is of a lower quality that the other three. I am not satisfied with this. I noted the following differences from the other three wheels.

• The spoke edges are markedly sharper due to a lack of finish radius.
• The spokes are noticeably thinner that the other three.
• The face edge radius is noticeably smaller.
• The masking between the spokes for the grey paint was sloppy.
• The finish of the grey paint on the back of the wheel is rougher and the machining marks are noticeable.

I reached out to the guys I bought them from and they are working with me on it so that's a good surprise. They said we could go through as many wheels in their inventory as need to find one that matches the others. Just need to coordinate a dismount and get there.

Here are some pics

Poor Wheel Edge:


Poor Masking and Rough Finish:


Sharp Spoke Edge


Good Wheel Edge:


Good Masking:

 

[gooffeyguy]

Damn, too bad you didn't notice that before you got the tires mounted

Sent from my SM-G930V using Tapatalk

 

[George B]

Damn, too bad you didn't notice that before you got the tires mounted

Sent from my SM-G930V using Tapatalk

Right! and it's on me. I am at a point in life where everything is an inconvenience so I feel rushed at everything. Then I F#&K up and have to redo stuff.

 

[Geoffsfas10]

Ordered my cabin filter retrofit kit

 

[George B]

I did fix a broken rear bumper tab with a bit of old bed liner and some plastic trim retainer things... was hard to get a good pic.

 

[Doubeleive]

Got the replacement overhead console and managed to install it without breaking anything this time

 

[George B]

Well, I need to slow down a bit.

While I was cleaning the wheels up a bit I noticed one wheel is of a lower quality that the other three. I am not satisfied with this. I noted the following differences from the other three wheels.

• The spoke edges are markedly sharper due to a lack of finish radius.
• The spokes are noticeably thinner that the other three.
• The face edge radius is noticeably smaller.
• The masking between the spokes for the grey paint was sloppy.
• The finish of the grey paint on the back of the wheel is rougher and the machining marks are noticeable.

I reached out to the guys I bought them from and they are working with me on it so that's a good surprise. They said we could go through as many wheels in their inventory as need to find one that matches the others. Just need to coordinate a dismount and get there.

Here are some pics

Poor Wheel Edge:
View attachment 249349

Poor Masking and Rough Finish:
View attachment 249350

Sharp Spoke Edge
View attachment 249351

Good Wheel Edge:
View attachment 249352

Good Masking:
View attachment 249353

Drove down to see these guys this afternoon. I am stunned by the level of customer service I received. They were ready for me and had a pallet with about 30 wheels on it. We opened boxes until I found the one I liked. They pulled my truck in and swapped the tire and sensor over at no charge and sent me on my way with a big thank you. I was not expecting that.

Link to the business: https://www.rpmtakeoffs.com/

They offer shipping too. Great guys!

 

[Geoffsfas10]

Drove down to see these guys this afternoon. I am stunned by the level of customer service I received. They were ready for me and had a pallet with about 30 wheels on it. We opened boxes until I found the one I liked. They pulled my truck in and swapped the tire and sensor over at no charge and sent me on my way with a big thank you. I was not expecting that.

Link to the business: https://www.rpmtakeoffs.com/

They offer shipping too. Great guys!

So they will sell wheels without tires then? looks like online all they have is combos but i wonder if you email they will send just wheels

 

[George B]

So they will sell wheels without tires then? looks like online all they have is combos but i wonder if you email they will send just wheels

They will ship just wheels.

 

[Tonyrodz]

Drove down to see these guys this afternoon. I am stunned by the level of customer service I received. They were ready for me and had a pallet with about 30 wheels on it. We opened boxes until I found the one I liked. They pulled my truck in and swapped the tire and sensor over at no charge and sent me on my way with a big thank you. I was not expecting that.

Link to the business: https://www.rpmtakeoffs.com/

They offer shipping too. Great guys!

All about customer service. A happy customer, is a repeat customer.

 

[Rocket Man]

Drove down to see these guys this afternoon. I am stunned by the level of customer service I received. They were ready for me and had a pallet with about 30 wheels on it. We opened boxes until I found the one I liked. They pulled my truck in and swapped the tire and sensor over at no charge and sent me on my way with a big thank you. I was not expecting that.

Link to the business: https://www.rpmtakeoffs.com/

They offer shipping too. Great guys!

That’s awesome customer service right there. Good to see it.

 

[Rocket Man]

Finished the cam swap in the Silverado today. Blackbear is a ways out on retunes so I’m trying to bribe them. It’s running a bit rough, idle is all over the place. I can tell the ECU is trying to figure it out but at least so far no codes. I think it’s gonna be lopey as hell.

 

[Derick]

11 bucks on Amazon later and my glass don't fall on me anymore. Yay.

 

[Rocket Man]

11 bucks on Amazon later and my glass don't fall on me anymore. Yay.

View attachment 249406

$11 for both?

 

[Doubeleive]

11 bucks on Amazon later and my glass don't fall on me anymore. Yay.

View attachment 249406

now to just fix that broken defrost tab

 

[Rocket Man]

now to just fix that broken defrost tab

Frost Fighter FTW