avalonandl
Full Access Member
I have to change the RH headlight bulb... whats the easiest way WITHOUT pulling the grille ?
The low beam went....ugh.
The low beam went....ugh.
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
- Thread starter phattyford
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Well replace all the bulbs while you're in there.
With my cai installed I can reach in from behind, just have to pop a plastic retainer out and pull the rubber guard back and reach inside
avalonandl
Full Access Member
Thanks...
swathdiver
Full Access Member
Way down on my To Do List is a Whelen SA315 to go with their PAP112, an electric air horn and microphone. Oh, and a SAK24 bracket made for our trucks but that will interfere with your transcooler.
swathdiver
Full Access Member
Any pics of the splash guards installed yet? I got my fronts on but not the rears yet.
Bigkevschopshop
Full Access Member
“It sounds like the combination an idiot would have on his luggage” dark helmet.
Bigkevschopshop
Full Access Member
Bought my oldest his first ride.
Tonyrodz
Resident Resident
Nice! How'd he like it? I really like these in 2 doors. Had one for years. Couldn't kill that 4.3. Trans is another story tho.
the_tool_man
Full Access Member
I've been a bit disappointed in mine. The first issue is that the rubber strip that sort-of seals against the rear body popped out the first week. I glued it back into its slot. But it worked itself out again a few weeks later. I ended up leaving it off, with no apparent consequence. Then last week, I noticed the center of it had distorted so that it sags a little below the contour of the roof. It's only low by about 3/16". And it's not super noticeable above my line of sight like it is. But still, I'd expected better after only 13 months.Ordered a 3rd brake light for the yukon will update after it gets here!!
Sent from my SM-G955U using Tapatalk
Last edited:
bigrhino
Full Access Member
Mine did the same thing.
gooffeyguy
Tom
I'll have to keep watch on mine. It's only been installed since early/mid December.
2001 Yukon SLT
2012 Yukon Denali XL
2011 Yukon Denali RIP 5/20/18
2001 Yukon SLT
2012 Yukon Denali XL
2011 Yukon Denali RIP 5/20/18
‘How many assholes are on this ship??’
‘Great, im surrounded by assholes!’
Would have been cooler if it was 78* LOL
George B
¯\_(ツ)_/¯
It would have been warmer...
Staggered 02
Full Access Member
- Joined
- Jul 5, 2019
- Posts
- 672
- Reaction score
- 1,556
Those brakes will look and perform great as you already know. I will be installing my redone brakes on the Crew Cab while I am sheltered at home. I don't like the fact that the lettering has faded off.
Staggered 02
Full Access Member
- Joined
- Jul 5, 2019
- Posts
- 672
- Reaction score
- 1,556
That was a good deal on the LSX intake.
Staggered 02
Full Access Member
- Joined
- Jul 5, 2019
- Posts
- 672
- Reaction score
- 1,556
No problem. I saw it when I was looking for an intake to replace the ugly stock one on my Silvy. But I don’t need anything near that one. 102 mm is good for what, 800 HP? I know the stock is good for 450-500. I just want a clean looking intake, I’ll probably get one of the welded aluminum ones idk.
That LSx Intake would look great in that engine bay. Cleans the engine bay up quite nicely.
That LSx Intake would look great in that engine bay. Cleans the engine bay up quite nicely.
Staggered 02
Full Access Member
- Joined
- Jul 5, 2019
- Posts
- 672
- Reaction score
- 1,556
What a difference those brakes make. Nice job.
