Finally posting a "build" thread. The progression of my stupidity.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
Took a lot longer than anticipated. But got the 14 bolt in and drove it home finally.
Unfortunately I do need to adjust the dust covers, because the wrecking yard and the ever-loving crud out of them, and the driver side is for sure rubbing somewhere when I drive, and the passenger side I heard squeak on the highway next to k rail, but not constantly.

I'll have to disassemble the 10 bolt at a later date and see what actually happened.

It's ridiculous how much of that stuff swaps over.
From what I had read, I was going to need some sort of conversion u-joint. This was not the case. I could have just pulled the straps off the 10 bolt, left the U-joint in the drive shaft and used those same straps and U-joint right back in the 14 bolt.
So a quick trip to the auto parts store to grab a Spicer 1350, and reuse the stock straps, and it's smooth as silk.
The only thing that needed any sort of change, was the spot the brake lines mount on the diff bracket.

But that was easily Bent by hand and bolted right up.


Also finally replaced my melted passenger side airbag helper spring since I have the springs out anyway.
 

Attachments

  • IMG_20211226_111705702_HDR.jpg
    IMG_20211226_111705702_HDR.jpg
    395.3 KB · Views: 5
  • IMG_20211226_145212673_HDR.jpg
    IMG_20211226_145212673_HDR.jpg
    447.7 KB · Views: 5
OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
Update on the squeaking / rubbing issue.
Probably not going to investigate into it for another couple hundred miles because it seems to have self clearanced already.
So I'll just wait until I have to do a tire rotation before pulling the wheels and brakes back off to see where it was actually touching.

Pulled the plugs out of every door. Rear driver side door has a bunch of junk in it that I might spend time trying to actually clean out later... But probably just let it rot out the door
Front passenger has what looks like a washer or something blocking the front drain hole. Was able to move it out of the way but not get it out of the door and it started draining some water.
Driver side door had a sunflower seed shell blocking it.
Rear passenger was dry as a bone.

Put the new Moog U-joint strap kit on.
 

Attachments

  • IMG_20220101_102816579_HDR.jpg
    IMG_20220101_102816579_HDR.jpg
    230 KB · Views: 5
  • IMG_20220101_104512189.jpg
    IMG_20220101_104512189.jpg
    234.1 KB · Views: 5
OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
There's some small things I'm sure i've forgotten to post here, but I suppose i should get back to it.
Got my Brian Tooley Racing afm/dod & vvt delete, truck norris cam and springs, some other tid bits.

Got tired of the dang plastic center caps cracking and bowties fogging up.
Got the PPV center caps, sprayed them with Steel-It, grabbed some doorman lugnuts, got hardware free99 from the day job leftovers.
Tried black lugs and caps, didnt really like it, chrome lugs black caps, still not really, then silver caps chrome lugs...and i thinks its just the smaller smoother look i actually dont care for with my off-road aesthetic.
That said, black wheels and caps would hide better.
 

Attachments

  • IMG_20220618_164451219_HDR.jpg
    IMG_20220618_164451219_HDR.jpg
    414.2 KB · Views: 6
  • IMG_20220618_190924107.jpg
    IMG_20220618_190924107.jpg
    366.7 KB · Views: 7
  • IMG_20220618_171635707_HDR.jpg
    IMG_20220618_171635707_HDR.jpg
    397.8 KB · Views: 7
  • IMG_20220618_172024380_HDR.jpg
    IMG_20220618_172024380_HDR.jpg
    393.2 KB · Views: 7
  • IMG_20220618_190855898.jpg
    IMG_20220618_190855898.jpg
    333.8 KB · Views: 6
OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
I've needed to fix the inline I made just so I could run the physical sensor, one end has been leaking for quite a while, especially when it goes over the base 43 PSI.

Apparently the ethanol was eating away at the black nylon or something.

So I need to fix that before I put it back on anyway.





I just need to put enough miles on the dumb thing to get all the sensors ready for the smog check.



But the stock intake back on and the stock tune also... Put in 20 gallons($125) of regular, physical sensor eventually settled on 22%.

With the stock tune and virtual sensor, it reads 3.5%. .. close enough to Eaton or less that it's not ******* it off, I might have to put another $50 in to water it down some more though, keep the fuel trims happy.



Forgot how gutless it feels on a stock tune. It's noticeably slower, especially in the mid-range and it doesn't feel like it pulls at all up top anymore.

And the shifts are so soft it's disgusting, even wide open you don't feel anything...



Kind of forgot how loud the intake really was as well. The stock intake is ridiculously quiet in comparison. But I kind of wondered what this exhaust setup sounded like, but I can never tell because the intake was so much louder. Haha



Pretty sure I'll be able to use the Corsa intake box with the Whipple intake tube, the couplers on the factory tube and the corsa tube line up almost perfectly.
 

Attachments

  • IMG_20220625_142544332~2.jpg
    IMG_20220625_142544332~2.jpg
    321.6 KB · Views: 6
  • IMG_20220625_143252135~2.jpg
    IMG_20220625_143252135~2.jpg
    294.4 KB · Views: 6
  • IMG_20220625_143439373~2.jpg
    IMG_20220625_143439373~2.jpg
    356.9 KB · Views: 6
OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
Well, got about a hundred miles on it so far, everything is ready except for the EVAP system...
Sort of running out of time here, not sure if it needs more cycles or if I do have an issue even though there's been no check engine light.
 

Attachments

  • Screenshot_20220628-132619.png
    Screenshot_20220628-132619.png
    316.3 KB · Views: 2

89Suburban

Bull in the china shop
Supporting Member
Joined
Jan 10, 2013
Posts
12,845
Reaction score
35,195
Location
SE PA
Hauled a Bicycle up to Santa Barbara to hang with a friend.
Put in a Pioneer 8500NEX + front and rear cameras.
Added a Optima Yellow Top battery as a secondary.
Took her down some firer roads with a buddy.
Found out the Driver's side engine mount was trashed.
Put some Ray Bestos R3oo rotors and Police pads on it and a new motor mount.
Took her to my buddies in-laws in Havasu.
Launched the boat a few times...parked it among it's family.
Pulled his boat home.



It's coming, I'm on the clock now. It'll have to wait. :'(


Dang that boat trailer parking looks like a cluster-F!!!!! How are people supposed to get in/out?? I thought my launch was bad LOL.
 
OP
OP
RooTBeeRthe1st

RooTBeeRthe1st

Full Access Member
Joined
Jul 11, 2018
Posts
1,020
Reaction score
2,347
Dang that boat trailer parking looks like a cluster-F!!!!! How are people supposed to get in/out?? I thought my launch was bad LOL.
Hard to tell from that picture, but there's actually a lot of space between everybody, but I did make sure to pull up to a spot where nobody would be in front of me as well
 

Forum statistics

Threads
128,788
Posts
1,805,458
Members
91,768
Latest member
PascalBlues
Top