BourbonNcigars
Full Access Member
- Joined
- Dec 1, 2018
- Posts
- 865
- Reaction score
- 1,841
Damn. We need a sound file uploaded for clear definition of engine sounds.
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
- Thread starter phattyford
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
gooffeyguy
Tom
Sounds kinky..... Lol
2001 Yukon SLT
2012 Yukon Denali XL
2011 Yukon Denali RIP 5/20/18
BourbonNcigars
Full Access Member
- Joined
- Dec 1, 2018
- Posts
- 865
- Reaction score
- 1,841
Sounds like a question you get asked after you pull out your $20 bill.
Ridin Solo
Brain Ninja
lol uhhhh...... sounds like a knock to me.. not the best video but its all i have at the moment.
swathdiver
Full Access Member
Lifter and either power steering or a/c compressor noise. Get out the stethoscope and poke around!
Hi-psi
Full Access Member
That sounds more valvetrain related to me.
sounds like a sticky lifter to me, my 03 does it off & on
Ridin Solo
Brain Ninja
As y'all have suggested, I also believe it is lifter noise... It only happens on cold starts (so far) and seems to go away after the engine warms up, do y'all reccomend I take it in to be checked out? I have had AFM disabled through my BB tune since I bought it at 20k miles (it now only has 76k miles) because I was hoping to avoid this issue, at least until a much higher mileage.
Hi-psi
Full Access Member
Do you have a warranty? If so, absolutely.
If you don't, just before your next oil change do a crankcase Seafoam treatment.
I've heard/read really good stuff about Kreen from Kano Labs, but it isn't as readily available as Seafoam.
If you don't, just before your next oil change do a crankcase Seafoam treatment.
I've heard/read really good stuff about Kreen from Kano Labs, but it isn't as readily available as Seafoam.
Ridin Solo
Brain Ninja
Wish I did but I don't because its not 2018 anymore so that puts me past the 5 year powertrain warranty period, unfortunately.
tore into the left headlight again today it was still intermittent, cleaned up the relay contacts, replaced the bulb, then as I was putting it back together I noticed my power lead was arcing on the frame thru a butt connector so I double insulated it and put some electrical tape on the frame hopefully that solves my problem.
Hi-psi
Full Access Member
Totally not Tahoe/Yukon/etc related....but, I may have to finally buy me one of these Oculus headsets.
qcon
Full Access Member
Had a busy Saturday. Added LED+resistors to the rear signals. switched to H9 headlight bulbs, and wired up front sequential turn signals.
CHOO CHOO
BackPagePhil
Sent you a pm buddy
See why i asked?
the_tool_man
Full Access Member
I had a little fun with some vinyl today. I blacked out the grille emblem and experimented with partially color matching the door handles. I also removed the rear GMC and the faded Flexfuel badge. I'm not sure if I like the handles or not.
mikeyss
Full Access Member
I like the handles!
93blkongreenpro
Full Access Member
- Joined
- Feb 9, 2016
- Posts
- 1,388
- Reaction score
- 1,358
I thought I was smelling burnt voice coil, but instead, I was smelling brake pad.
Now I need to take it apart and grease the slide pins and clean the hardware I guess and make sure everything is moving smoothly. Hopefully the pads are fine.
Sent from my SM-N950U using Tapatalk
Now I need to take it apart and grease the slide pins and clean the hardware I guess and make sure everything is moving smoothly. Hopefully the pads are fine.
Sent from my SM-N950U using Tapatalk
Fosscore
Full Access Member
- Joined
- Apr 16, 2014
- Posts
- 10,864
- Reaction score
- 19,741
I like the handles. And the rear removal is a good delete.
the_tool_man
Full Access Member
I may replace the rear YUKON with DENALI. Having it match the doors appeals to my OCD. Credit for the handles goes to mazdawg. I saw him do it first.
Last edited:
