What did you do to your OBS GMT400 Tahoe/Yukon Today?

[DallasTahoe]

Got tired of inconsistent brakes so I got my nbs master cylinder and my simple brake proportioning valve set up and ready for my ABS delete installation tomorrow (crossing fingers)

Sent from my iPhone using Tapatalk

 

[Kelsda]

Fuel,oil,air filters-oil,plugs,wires,cap,rotor,pcv,and a tire rotation should have pulled trailer out of garage brrrr very frigid out

 

[DallasTahoe]

Finished up my nbs master cylinder upgrade and my abs delete with no big issues and I didn’t even have to take the abs warning light bulb out of the dash, she stops pretty dam good even before doing a brake bleed, that’s next!

Sent from my iPhone using Tapatalk

 

[Danny3737]

No you don't. 80+ degrees in December ruins any Christmas spirit there is. And it's just garbage to be sweating 12 months out of the year! LOL

I’ll take the heat over the cold any day

 

[edonwheels73]

Well I traded my 94 2 door for a 94 crew cab dually but I'm still going to keep following this forum.

Sent from my SCH-I545 using Tapatalk

 

[1BADI5]

Installed this in the Yukon today.

I got all of the lines for the backup camera run, BT Mic installed; just need to get the camera mounted on the back of the truck (under the bumper)

The camera and streaming music via BT is an amazing function to have.......its going to be great for commuting

 

[1BADI5]

FYI - if you have a rear view mirror with the temp or auto dimming....... you can tap the harness under the A-pillar plastic. Its a green wire, I used a test light to verify the wire

The other 2 option are - 1) reverse lock out harness on the side of the transmission 2) tap the reverse bulb wiring at the back of the truck

 

[jiggie]

Got some new tires yesterday. Ditched the junk bridgstones. Went from the stock p255/70/16 to a LT265/70/17 all terrains in 10ply. Chose these cause well first they were affordable, 2nd they had good ratings on tire rack and they have the 3 peak mountain snow flake symbol on the side so ill be cdot compliant when we go to colorado in a few weeks.

Sent from my LG-M153 using Tapatalk

 

[99blackburban]

Took my stock exhaust manifolds off in preparation for my new pacesetter long tubes, then had to deal with this

 

[PG01]

Took my stock exhaust manifolds off in preparation for my new pacesetter long tubes, then had to deal with thisView attachment 190463 View attachment 190464

Nice center punch... looks exact.... lol..

 

[edonwheels73]

Started cleaning yesterday I think I need to just pull dash apart and clean as I put it back together. All the vents looks like this.

Sent from my SCH-I545 using Tapatalk

 

[PG01]

Started cleaning yesterday I think I need to just pull dash apart and clean as I put it back together. All the vents looks like this.

Sent from my SCH-I545 using Tapatalk

Ughh

 

[1BADI5]

Well today was new hub assemblies and new brake pads....... easy work!

The pedal feeling with new pads is amazing! I'm really impressed with the Duralast Gold pads..... I normally buy either Hawk or EBC

 

[99YukonSLT]

Gonna pull my yukon into work overnight friday to let it sit and warm up so I can come in saturday and change the oil, trans fluid, remount my fogs, and figure out which ABS sensor or hub is bad causing the ABS to kick in at slow speeds. Probably throw my tow hooks back on and give it a good once over.

 

[jiggie]

Decided to get some new wheels today. Wife picked out the wheels. Didn't want chrome or super flashy wheels. Just something classy looking. Went 22s with 305/40 tires so i still have good sidewall and so it would fit in the garage. Did 24s first and the roof rack hit the garage door lol.

Sent from my LG-M153 using Tapatalk

 

[1BADI5]

Got the 2" blocks in so the lift is complete (torsion bar crank & RC UCAs)

Tomorrow is Proforged inner/outer tie rods, Proforged billet sleeves and MOOG K100335 2* adjustable cam bolts

Then off to get an alignment at Extra Mile Performance, in Odenton, MD

 

[1BADI5]

Inner/outer ties and sleeves done............. yup, needs the pitman arm and idler arm.

**** it........ new pitman, Idler arm and idler arm bracket. I'm doing it all and done.

 

[Kelsda]

Changed out right side washer nozzle picked up a few at the local bone yard no charge

 

[1BADI5]

can't beat free 99

 

[jiggie]

Decided to get some new wheels today. Wife picked out the wheels. Didn't want chrome or super flashy wheels. Just something classy looking. Went 22s with 305/40 tires so i still have good sidewall and so it would fit in the garage. Did 24s first and the roof rack hit the garage door lol.

Sent from my LG-M153 using Tapatalk

After a week decided these are not the look were going for. Tire shop is letting us return them and might swap wheels for some oe reps like this

Sent from my LG-M153 using Tapatalk