Trail Armor for Yukon/Tahoe?

[JerGood]

Hey all.... I have a 2003 Yukon XL. I have a lot of rocker panel rust like I'm sure a lot of others do with this age of SUV. I found a product that covers the rocker panels via Bushwacker that looks really cool. Unfortunately they only make them for GM trucks and Jeeps right now. I'm wondering if anyone else here would buy them if they made them for Yukon/Tahoes. Maybe if enough folks are interested they would make them?

http://www.bushwacker.com/trail-arm...-cab-pickup-rocker-panel-oe-matte-black-14067

 

[MA_hoe]

i dont know about you but plastic and trail armor dont go together. just saying...

 

[jimweis]

I just purchased a set for a crew cab, they will need modification. Mine has some bubbles and rust staining, no holes yet. Tahoe plastic sills go out into the sill more than the pickup, will need trimming there and the rear length.

 

[jimweis]

I just purchased a set for a crew cab, they will need modification. Mine has some bubbles and rust staining, no holes yet. Tahoe plastic sills go out into the sill more than the pickup, will need trimming there and the rear length.

 

[jimweis]

These are for a crew cab, needed some cutting slip in between the rocker and the step. I slotted holes and slipped them in under the bracket bolts. Nice rust hide

 

[corvette744]

Nice job...

 

[moosehead]

These are for a crew cab, needed some cutting slip in between the rocker and the step. I slotted holes and slipped them in under the bracket bolts. Nice rust hide

Looks good. How much did thst cost?

Sent from my SM-G930V using Tapatalk

 

[jimweis]

$200 Ebay
https://www.ebay.com/itm/14067-Bushwacker-Trail-Armor-Rocker-Panel-Guard-Silverado-Sierra-Crew-Cab/302199036290?ssPageName=STRK:MEBIDX:IT&_trksid=p2060353.m2749.l2649

Extended cab may work, since the sill area will need cut off.
I used my radial arm saw ripping setup.

 

[BigDaddy13440]

Me likey! Now if they only made covers for the rear quarter panels to match.

 

[jimweis]

Nice job...

Nice not to have the rust streaks. I finally cleaned the rust off the steps with CLR.

 

[Davidh]

How would they work with out the step on their. Those look really sharp just what I was looking for.


Sent from my iPhone using Tapatalk

 

[jimweis]

I'm working on fashioning pieces for the lower front fenders, I don't like it stopping at the rocker.

 

[jimweis]

How would they work with out the step on their. Those look really sharp just what I was looking for.


Sent from my iPhone using Tapatalk

Yes

 

[jimweis]

I finished the small filler at the bottom of the fender, using scrap cut-offs, formed it with the heat gun.

 

[Tonyrodz]

Nice not to have the rust streaks. I finally cleaned the rust off the steps with CLR.

How are they holding up?

 

[jimweis]

How are they holding up?

Two years later they look like the day I put them on.

 

[project_x]

Jim, @jimweis
I know this is an old thread... looking to do the same now that i replaced the rockers on my suburban...
How did you cut yours?

Thanks,
Rob

 

[jimweis]

Good tin snips.

 

[Aquamania001]

OK! Just found this and these are PERFECT for my truck. Ordering now!!!! By the way they look great on your truck.

 

[jimweis]

OK! Just found this and these are PERFECT for my truck. Ordering now!!!! By the way they look great on your truck.

Thanks, they are holding up nice, I can't believe they have been on 7 years.