Solved. Truck Norris cam install need help!

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Byoung1330

Full Access Member
Joined
Aug 26, 2018
Posts
446
Reaction score
294
Location
Cookeville tn
What’s up guys. I got a 04 tahoe 5.3 LT flex fuel 2wd. I upgraded timing chain oil pump did the truck Norris camshaft .560 springs that come with it an the seals. Also they said 7.400 pushrods will be fine. I have stock heads and lifters still. They’ve never gave a problem or sounded bad. Engine is quiet. Installed everything an had it tuned. Sounds awesome. After the engine warms up I hear a tick. Found broken manifold bolt bought one them dorman exhaust clamps. Anyway engine is very quiet when I start it an after I warms up I can hear a slight tap while driving. When I get on the gas a little it goes away. After doing a bunch of research I see lifter pre load an all this. I should probably buy a pushrod checker an make sure the length is right. But it’s kinda confusing. I get to check for zero lash an count the turns an all that. I’m not 100 sure how much pre load stock lifters need. The web is full of pre load for ls7 lifters. I pulled my valve covers off an u can spin the pushrod with your finger tips. Not easily but u can. I pulled one pushrod out an installed 7.425. Can’t spin it. Wondering if that would be to long. The guys at Brian tooley said the 7.400 should be fine. An I’ve heard these ls motors have a tap that’s normal after cam install.
 

S33k3r

Full Access Member
Joined
Aug 14, 2017
Posts
2,254
Reaction score
2,977
Location
Dallas, Texas
What oil are you running? I'm thinking a slightly thicker oil, or maybe a slightly different type of oil may solve your problem. It definitely sounds like something is expanding with heat, so it's always possible it's something else. I'd recheck all of your exhaust, for example.

Just my $0.02 worth.
 
OP
OP
Byoung1330

Byoung1330

Full Access Member
Joined
Aug 26, 2018
Posts
446
Reaction score
294
Location
Cookeville tn
I have done some experiments so far lol. I’ve ran castrol edge with titanium in 5w30 an 10w30 an yesterday went to penzoil platinum 5w30 An I’ve tried wix filters an yesterday threw a Mobil one on.
 
OP
OP
Byoung1330

Byoung1330

Full Access Member
Joined
Aug 26, 2018
Posts
446
Reaction score
294
Location
Cookeville tn
What oil are you running? I'm thinking a slightly thicker oil, or maybe a slightly different type of oil may solve your problem. It definitely sounds like something is expanding with heat, so it's always possible it's something else. I'd recheck all of your exhaust, for example.

Just my $0.02 worth.
And I did check my exhaust after putting the clamp on the broke bolt
 

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,100
Reaction score
25,031
Location
Treasure Coast, Florida
What’s up guys. I got a 04 tahoe 5.3 LT flex fuel 2wd. I upgraded timing chain oil pump did the truck Norris camshaft .560 springs that come with it an the seals. Also they said 7.400 pushrods will be fine. I have stock heads and lifters still. They’ve never gave a problem or sounded bad. Engine is quiet. Installed everything an had it tuned. Sounds awesome. After the engine warms up I hear a tick. Found broken manifold bolt bought one them dorman exhaust clamps. Anyway engine is very quiet when I start it an after I warms up I can hear a slight tap while driving. When I get on the gas a little it goes away. After doing a bunch of research I see lifter pre load an all this. I should probably buy a pushrod checker an make sure the length is right. But it’s kinda confusing. I get to check for zero lash an count the turns an all that. I’m not 100 sure how much pre load stock lifters need. The web is full of pre load for ls7 lifters. I pulled my valve covers off an u can spin the pushrod with your finger tips. Not easily but u can. I pulled one pushrod out an installed 7.425. Can’t spin it. Wondering if that would be to long. The guys at Brian tooley said the 7.400 should be fine. An I’ve heard these ls motors have a tap that’s normal after cam install.
See if you can isolate the source of the sound with a long extension to your ear or mechanic's stethoscope.
 

iamdub

Full Access Member
Joined
Apr 23, 2016
Posts
20,712
Reaction score
44,433
Location
Li'l Weezyana
I actually figured it out. I went from 7.400 pushrods to 7.425 an it took all the noise out. More lifter pre load

Interesting. I'm wondering what the base circle diameter is of that cam. They're usually .050" smaller, meaning you'd need a .025" longer push rod. Stock is 7.385". Add .025" to that and you get 7.410". Other than custom order, aftermarket push rods come in .025" increments and 7.400" is the closest to that 7.410". You're at .040" longer than stock as if the cam's base circle is much more than .050" smaller than stock.

In chasing a light ticking only within a specific RPM range, I recently measured all of my lengths to zero lash and preloads. My four longest lengths to zero lash are tied at 7.28125". With the 7.350" push rods I'm running, that's .06875" preload. Going one step up to 7.375" would put those at .09375" preload.

I'm tempted to try it. I was looking at the two highest preloads of .100" thinking those were the source of my noise. I haven't ruled it that they aren't. But, maybe it's the four lowest ones. I could tackle it from both ends and get four longer rods and two shorter ones. As it sits, I have a .03125" spread between lowest and highest. Reducing the two with .100 to .075" and increasing the four with .06875" to .09375" would tighten that spread to only .01875". Lowest would be .075" and highest would be .09375". The rest would be .08125" and .0875".


Yeah... I'm not expecting you or anyone to actually absorb any of that. :D
 
Last edited:

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,100
Reaction score
25,031
Location
Treasure Coast, Florida
Interesting. I'm wondering what the base circle diameter is of that cam. They're usually .050" smaller, meaning you'd need a .025" longer push rod. Stock is 7.385". Add .025" to that and you get 7.410". Other than custom order, aftermarket push rods come in .025" increments and 7.400" is the closest to that 7.410". You're at .040" longer than stock as if the cam's base circle is much more than .050" smaller than stock.

In chasing a light ticking only within a specific RPM range, I recently measured all of my lengths to zero lash and preloads. My four longest lengths to zero lash are tied at 7.28125". With the 7.350" push rods I'm running, that's .06875" preload. Going one step up to 7.375" would put those at .09375" preload.

I'm tempted to try it. I was looking at the two highest preloads of .100" thinking those were the source of my noise. I haven't ruled it that they aren't. But, maybe it's the four lowest ones. I cold tackle it from both ends and get four longer rods and two shorter ones. As it sits, I have a .03125" spread between lowest and highest. Reducing the two with .100 to .075" and increasing the four with .06875" to .09375" would tighten that spread to only .01875". Lowest would be .075" and highest would be .09375". The rest would be .08125" and .0875".


Yeah... I'm not expecting you or anyone to actually absorb any of that. :D
You seem like an excellent candidate for adjustable pushrods or rockers!
 

George B

¯\_(ツ)_/¯
Joined
Feb 5, 2020
Posts
7,618
Reaction score
18,029
Location
Oconomowoc, Wisconsin 53066
Interesting. I'm wondering what the base circle diameter is of that cam. They're usually .050" smaller, meaning you'd need a .025" longer push rod. Stock is 7.385". Add .025" to that and you get 7.410". Other than custom order, aftermarket push rods come in .025" increments and 7.400" is the closest to that 7.410". You're at .040" longer than stock as if the cam's base circle is much more than .050" smaller than stock.

In chasing a light ticking only within a specific RPM range, I recently measured all of my lengths to zero lash and preloads. My four longest lengths to zero lash are tied at 7.28125". With the 7.350" push rods I'm running, that's .06875" preload. Going one step up to 7.375" would put those at .09375" preload.

I'm tempted to try it. I was looking at the two highest preloads of .100" thinking those were the source of my noise. I haven't ruled it that they aren't. But, maybe it's the four lowest ones. I cold tackle it from both ends and get four longer rods and two shorter ones. As it sits, I have a .03125" spread between lowest and highest. Reducing the two with .100 to .075" and increasing the four with .06875" to .09375" would tighten that spread to only .01875". Lowest would be .075" and highest would be .09375". The rest would be .08125" and .0875".


Yeah... I'm not expecting you or anyone to actually absorb any of that. :D
I’m tryn…
 

Forum statistics

Threads
128,791
Posts
1,805,528
Members
91,775
Latest member
labans
Top