iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
[yt]kzuKZnw64Ck[/yt]
[yt]eBijleHc5RM[/yt]
[yt]8qbvrGg5sgY[/yt]
[yt]eBijleHc5RM[/yt]
[yt]8qbvrGg5sgY[/yt]
Last edited:
My Yukon
- Thread starter iwaslowr
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
tast101
Full Access Member
Here you go:
[yt]kzuKZnw64Ck[/yt]
[yt]eBijleHc5RM[/yt]
[yt]8qbvrGg5sgY[/yt]
PImp Kon too.
Last edited:
foreverfalcon40
Full Access Member
- Joined
- May 3, 2009
- Posts
- 2,082
- Reaction score
- 5
SHIT IS ***** FRESH TO DEATH! NICE NIEGHBORHOOD TOO!
Did you have to raise it to fit?
X2 On Backing up into the Driveway. I think it elevates the house and the ride! I do it all the time!
Did you have to raise it to fit?
X2 On Backing up into the Driveway. I think it elevates the house and the ride! I do it all the time!
Timmy
Full Access Member
looks real good
OP
OP
iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
Thanks for the compliments! 
It did not have to be raised for them to fit... the suspension is stock (for now) and there is only slight rubbing on the plastic fenderwell lining during partial turns. There is no rubbing at full lock turns such as U-turns.
My lowering kit arrived but has not yet been installed:
It did not have to be raised for them to fit... the suspension is stock (for now) and there is only slight rubbing on the plastic fenderwell lining during partial turns. There is no rubbing at full lock turns such as U-turns.
My lowering kit arrived but has not yet been installed:
jmildoc
Full Access Member
Where you at in texas?
OP
OP
iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
Austin
blueflamed03
Elite Member
nice ride man!!
foreverfalcon40
Full Access Member
- Joined
- May 3, 2009
- Posts
- 2,082
- Reaction score
- 5
OMG...How much are you gonna lower it? I assume your going to cut out the plastic that rubs when you drop it?
OP
OP
iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
The kit will allow up to 4 inches of drop in front and rear but I don't see myself going lower than 2/3. There will be slight cutting of the plastic... but only when the heat gun treatment doesn't do the trick.
Timmy
Full Access Member
sounds like a good plan.
JKmotorsports
Rollin the boosted grocery-getter
Truck's looking real good man!
Thanks Tast!
DarkTahoe00
Full Access Member
The Kon is Hot man! What kinda reverse lights you got there are bright as hell!
OP
OP
iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
Thanks!
They are 8000K H11 HID's, got the idea from "Laredo Texas" on the TahoeForum site. It was a very simple install. The only issue I encountered was having to removing a tab from each bulb so it would seat flush against the housing... silicone was used to hold it in place and provide a seal. There are now two additional connectors (harness to ballast and ballast to bulb) which need to be disconnected when the tail light housing is removed... but it's worth the hassle. They are much brighter that the stock bulbs and are great when reversing or entering the Yukon in dark areas.
turboeclips
Full Access Member
nice clips.... makes me want to get exhaust now.
R.Beezy
Costco Member
the truck is mean bruh
OP
OP
iwaslowr
ɹǝqɯǝɯ ɹoıuǝs
yukon07Artic
Full Access Member
iwasslowr that kon cannot be anymore cleaner. sick looking truck. i was never a fan of billet grilles but your billet blows everything out of the water. Omg the 26' i always thought that was overdoing it but looking at your clip made me speechless. i always questioned the debadging and demolding but everything about your truck makes me want to jump the band wagon. to make long story short that fuc^en truck is sick!
Similar threads
