What did you do to your NBS GMT800 Tahoe/Yukon Today?
- Thread starter vwbeaner
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Night Fury
Full Access Member
removed the broken hanging passenger fog light from the crash. looking for pricing on front bumper, lower foglight valance and foglight. anybody got a good place i can look for them cheap?
ajaxnxs
Full Access Member
Southernstyle
Member
just washed mine inside n out for the first time in 2 months. lol it reeaaalllly needed it. im seriously thinking about going get some 3m wheels and pulling off some bagdes and those trim panels (with the chrome strip)on the outside of the doors. yeah why the hell not!!!
Night Fury
Full Access Member
i took the badges off but kept the moldings. (panels) it looks clean if you have chrome rims.
Attachments
ajaxnxs
Full Access Member
Today I replaced a battery after the Kon and I ran out of gas right infront of the pump because the battery died as i was trying to turn into the gas station. Spent 2 hrs in East TX heat trying to get the dag on thing started and then jumped. Finally called the dealer where i got it from for them to tow it and fix her. They put in a new battery. I go to get the alignment done @ Many Moe and Jack's (Pep Boys) and when they were done had them test the charging system just to tell me what i thought this afternoon, I have a bad alternator! So now I have to take the Kon back to the dealer again in the morning to get them to replace the Alt so i dont chew through another battery!
DaRosa218
The Dude abides
Got the keys and spacers in. I think it turned out nice 
Will post pics as soon as I have a wifi connection
Will post pics as soon as I have a wifi connection
got hoe back from the body shop and mechanic after almost 6 weeks.
smoked the tailes
installed - slim line in channel window vents 5% tint..
smoked the tailes
installed - slim line in channel window vents 5% tint..
Doomsta510
Full Access Member
Just purchased an 01 center console off eBay for $75 shipped! B^]
05Yukon23
Full Access Member
Test drove a 2011 wrangler rubicon to put the fear if God in her... Now I want one and the Yukon is still acting up...
Night Fury
Full Access Member
pics!
DaRosa218
The Dude abides
Took some nice Pics of the 'Hoe finally...... Can you say new sig Pic?! LOL
DaRosa218
The Dude abides
Thanks Mike!
Night Fury
Full Access Member
SICK! New sig too.
DaRosa218
The Dude abides
yukon2004
Full Access Member
I finally replaced the motor and regulator for my rear driver's window. Has been stuck a couple of inches down for the past 3 weeks. I don't even know if it was the motor or the regulator that was bad, but I figured if I'm going to tear the door apart, I might as well replace both. Also took off the "window rain guard" thingys. They were on there when I bought it the Yukon, and just never messed with it until today... looks a lot better without them!
With the new motor/regulator half installed:
The old motor/regulator:
---------- Post added at 09:06 PM ---------- Previous post was at 09:03 PM ----------
And yes... that IS a ratchet that I have wedged into the door... I was using it to hold the window up, lol.
With the new motor/regulator half installed:
The old motor/regulator:
---------- Post added at 09:06 PM ---------- Previous post was at 09:03 PM ----------
And yes... that IS a ratchet that I have wedged into the door... I was using it to hold the window up, lol.
MrBalll
Full Access Member
Removed the molding on the driver side. Lot easier than the rear emblems to remove and clean up. Not sure why, but it was. Passenger side tomorrow.
yukon2004
Full Access Member
What all is involved with removing the molding? It's not bolted or screwed in, right? How do you clean it up afterwards/what kind of mess is left behind? Thanks!
Similar threads
