LED dash pics and specs and crap

[haks310]

I don't even remember to tell you the truth.

Yup, same bulbs, 194s

 

[the big blue bus]

allright thanks. does 37 seem bout right for all of them? dont know when im going to do this project but when i do i want to get all the ones i need at one time and do it right.

 

[AtomicHoe094]

haha damn, this was an old thread, i was trying to remember if i even made it back in the day lol

 

[the big blue bus]

haha damn, this was an old thread, i was trying to remember if i even made it back in the day lol

haha i know guys but would you rather me start a new thread

 

[xX Mavr1ck Xx]

I thought that the 4wd had to be soldered correct?

 

[AtomicHoe094]

haha i know guys but would you rather me start a new thread

true true, you a good noob! lol and i thought it had to be soldered too :/ beats me, i dont have 4wheel drive

 

[the big blue bus]

true true, you a good noob! lol and i thought it had to be soldered too :/ beats me, i dont have 4wheel drive

well crap then. ill have to take it off one day and check it out, wish it was plug and play but me or my dad could solder a new one in there if neccessary

 

[haks310]

i only want to do the guages heater controls and 4wd indicator since thats burnt out, and its dark down there at night.

He has a floor shifter, those use two 194 bulbs.

Push button 4x4s have to be soldered in.

 

[the big blue bus]

He has a floor shifter, those use two 194 bulbs.

Push button 4x4s have to be soldered in.

yes i do so then its just a plug and play deal? thats what i want to hear

 

[haks310]

Yes sir.

 

[the big blue bus]

thank you haks310

 

[the big blue bus]

apon looking at it today seems im missing the drivers side courtesy light but i have the passenger. so from the thread posted a lil while back those 4 bulbs should be the same ones? and should i get the wled-x5s with 220 degree or would i be good with say the wled-x with 120 degree light or even the 90 degree ones? im not woried about hot spots there so i guess i dont need the wide angle ones and the 120 ones are cheaper by a lot. im going to order new ones of those and 4wd thing for now. will do guages when i do new radio

 

[Devious_Tahoe96]

Hey Haks what type of bulb is the 4x4 push button???

 

[haks310]

It is soldered in so you can use whatever bulb fits in there.

 

[Devious_Tahoe96]

so 194 would be the best bet since their small right??

 

[haks310]

T1.5 or NEO wedge bulbs are smaller.

But I am sure you can just go to Radioshack and pickup a couple of LEDs from there and they would work.

 

[jpaeltz]

Nice.

 

[Devious_Tahoe96]

How do you replace the license plate bulbs?? do you have to remove the bumper??? Thinking of putting WLED-x-x LED bulb UV Blacklight bulb since my license plates are white im thinking it'll stand out. Any opinions on that or should i just use a white led instead??

 

[haks310]

White.

Crawl your ass under there and check it out. Getting dirty is not a bad thing.

LoL and GM isn't dumb enough to make you remove the whole bumper to replace two light bulbs. Get under there behind the plate..you'll see the two sockets on each side...twist those out and you'll be able to get at the bulbs, simple plug and play.

 

[Devious_Tahoe96]

Well eventually i'll have to crawl under to replace the bulbs lol but thanks for the help haks