What did you do to your NBS GMT800 Tahoe/Yukon Today?

[Mechahead]

I still prefer the LEDs. Much smoother line.

 

[Big Buttons]

Keep the leds

 

[seven9st surfer]

Completely disassembled and correctly reassembled the K&N CAI that the shop apparently screwed up when they installed it for the previous owner (mass air sensor installed backwards), cleaned the air filter, de-rusted and sealed up a turn signal socket that was going bad, fixed my HID headlight, replaced a burnt out license plate light, replaced a rusted out wiper arm, and repaired a wire to my OBD port that somehow got cut in half so now my Bluetooth reader works again. Good day.

EDIT: and keep the LEDs, YukonGK, I have the same ones. They look great.

 

[UGA Tahoe]

yeah i like the LED's much better

 

[coolchuck]

I made it carry a dresser today.

Keep the LEDs.

 

[02 Burb]

+1 for the leds.

Removed the roof rack and used m6 set screws and silicone to fill the holes and re-sprayed some paint on the front to fix it up.

 

[mharders]

Clean burb^ I like it!

 

[02 Burb]

Clean burb^ I like it!

Thanks man

 

[ryan04z71]

Got the torsion bars cranked, fresh alignment, got some 285/70s installed. Tested the 4wd a bit.
Sorry for the pic of the camera, uploading from my phone right now. Haven't uploaded pics from camera yet


Sent from my XT1080 using Tapatalk

 

[Z-56 Hoe]

It's raining and my truck is filthy, so I can't get a good comparison pic to the first pic I'm posting, but here goes.....

LEDs all the way!

 

[Yukongk]

Rinseless washed her today. I think I'm going through an "anti-LED" phase and am rocking the smoked stock tails for a few more days lol.

 

[jdpber]

Hit the washer fluid switch cleaned a few bugs ... That was it

 

[Yuko04]

Getting ready to do 6 hi mod that I've been getting around to for the last year[emoji57]

 

[07Burb]

Darn blocking of license plates! I was going to come teepee your house

 

[Yuko04]

Darn blocking of license plates! I was going to come teepee your house

Its a pic I sent to a guy last week. He wants a front end like mine. Never can trust the CL guys.

 

[Yukongk]

Realized my brand new fog light has a flood inside of it......

 

[jomulk56]

Installed an Insys intake and LED plate light bar

Intake

Untitled by jomulk56, on Flickr

Plate light installed

Untitled by jomulk56, on Flickr

 

[JochenWoern]

Getting ready to do 6 hi mod that I've been getting around to for the last year[emoji57]
View attachment 26261

DANG, ........ Life must be rough if you have your own lift at home in your garage. ;-)

---------- Post added at 11:55 PM ---------- Previous post was at 11:54 PM ----------

Realized my brand new fog light has a flood inside of it......

Drill a small hole in the bottom of your fog light in order for the water to drain out. This should eliminate future floods as well.

These darn things NEVER seem to be watertight.

 

[seven9st surfer]

Got this little problem fixed today. I was doing about 2 mph in a turn lane when the truck started pulling like crazy to the right. The rear bolt for the front right upper control arm was just gone. And about 5 minutes earlier I was doing 75 over a pretty high bridge.

 

[JochenWoern]

Got this little problem fixed today. I was doing about 2 mph in a turn lane when the truck started pulling like crazy to the right. The rear bolt for the front right upper control arm was just gone. And about 5 minutes earlier I was doing 75 over a pretty high bridge.

Guess you were pretty lucky!!!!!