Search results

  1. jasonconway5

    Big brake kit help needed

    Someone suggested EBC rotors and pads. Anyone tried these?
  2. jasonconway5

    Big brake kit help needed

    what years did they put the dual piston calipers in that are a direct bolt up to my 2000 Tahoe new body style and will the rotors fit it as well?
  3. jasonconway5

    Big brake kit help needed

    Thanks! Where csn I find it???
  4. jasonconway5

    Big brake kit help needed

    Its about time for brakes, but I don't want to waste money on the stock brakes. I have 18" wheels and 285/65/18LT Nitto grappler tires. They are very heavy and make this tank even harder to stop. What's the most inexpensive big brake setup I can get thats going to actually make a difference on...
  5. jasonconway5

    I need this center cap, HELP!

    Nope, not even close. These slide through the center of the wheel. Mine bolt to the wheel and cover the lugnuts
  6. jasonconway5

    pissed!!!!!!!!

    Just going to leave this here for anyone else who may have this problem. Took me alot of time of reading, but sense I got my KS from ebay as well, im going to get some from the stealership tomorrow and see if this is my problem as well as this guys was...
  7. jasonconway5

    PCM question???????????

    I have a 2000 Tahoe 5.3 and I think it may need a PCM. What year range can I look to pull one from?
  8. jasonconway5

    I need this center cap, HELP!

    Still no luck
  9. jasonconway5

    MAF again!!

    Good question
  10. jasonconway5

    Factory Sub Replacement is here!

    Factory sub and amp are 2 ohm. Says 2 ohm on the magnet, but I tried it both ways and 2 ohm sounds best. Now I've got to do the rest of the speakers. Any suggestions? I paid $47 for the sub, just fyi on my spending range.
  11. jasonconway5

    MAF again!!

    How does it run bad? I think mine is bad but can't tell. No codes for it. Sometimes it act like its not getting fuel, happens more often within the first 5 minutes of start up.
  12. jasonconway5

    Question: Truck roll after shift to park?

    Always set the emergency brake when on even the slightest of hills. Otherwise, you put a load on the transmission, not good for it.
  13. jasonconway5

    pissed!!!!!!!!

    I got the el cheapos from ebay after reading good reviews. paid $25 for both. I replaced one of the harness connectors because the plastic broke the other connector was fine, no corrosion. If im not mistaken, the PCM is supposed to be putting out 5V TO the sensors themselves. Im going to check...
  14. jasonconway5

    Factory Sub Replacement is here!

    Thanks, yeah that sounds much better
  15. jasonconway5

    Factory Sub Replacement is here!

    Just got my Polk Audio DB840dbc in the mail. I chose this unit for my factory sub replacement based on several reviews in this forum and others. My question is, do I make it 2 ohm or 4 ohm? which sounds better? How do I change it from dual 4 ohm to 2 ohm if 2 is better? im confused on how to...
  16. jasonconway5

    pissed!!!!!!!!

    checked the voltage from the pcm to the connector at the connector and it was only reading 0.013 with the key switched on and engine off. is this too low? whats it supposed to read? ---------- Post added at 08:03 PM ---------- Previous post was at 07:04 PM ---------- Any voltage experts in here?
  17. jasonconway5

    pissed!!!!!!!!

    Bosch platinums. Was told to get ac delco.
  18. jasonconway5

    pissed!!!!!!!!

    Cleared the codes, drove it 20 miles home and it only gave me the code for 1 sensor, the bank 1 knock sensor. Not sure which one that is, but either way, the problem Still exists. Someone said to check the alternator for ac volts which can cause issues with sensors. Anyone heard of this?
  19. jasonconway5

    pissed!!!!!!!!

    Ok, so changing the gap didn't fix the problem. Added lucas to the oil and 108 octane booster. Cleared thecodes and even reset the fuel trim level (Disconecting the battery cables and touching them together for 10 seconds and leaving the battery disconnected for 20 mins) drove to work the...
  20. jasonconway5

    pissed!!!!!!!!

    Yes, both were fine as far as corrosion goes. However, one broke when I discinnected. The plastic just fell apart, so I replaced that connector. Just squeezed the spark plug gap own to .040, going to go drive it and see what happens. Also, would a bad maf sensor cause a lean mix which would...
  21. jasonconway5

    pissed!!!!!!!!

    P0327 and p0332, feels like runs a little better, not much, could be just do to the new intake gaskets. Slight rocker rattle under low rpm load still, don't know if that's due to the knock sensors retarding the timing or what. Going to check spark plug gap and try 93 octane to see if that fixes it.
  22. jasonconway5

    pissed!!!!!!!!

    Thanks
  23. jasonconway5

    pissed!!!!!!!!

    Bump
  24. jasonconway5

    pissed!!!!!!!!

    Nobody?
  25. jasonconway5

    pissed!!!!!!!!

    Nothing pisses me off quite like spending hours replacing a part and it not fixing the problem. I had knock sensor codes so I replaced them and intake gaskets. Cleared the codes, Drove it 3 miles and the damn knock sensors read low input on both. Wtf!?!?!?!?!?!?!?!?!,!,! I'm so sick of fighting...

Forum statistics

Threads
129,276
Posts
1,813,182
Members
92,384
Latest member
rick9667

Latest posts

Top