Rear passenger axle fitment

[Fless]

What do you mean by short and long? Because that's why I haven't ordered yet. Because I seen different lengths and I don't know which one I have

Short truck body, long truck body.

 

[swathdiver]

What do you mean by short and long? Because that's why I haven't ordered yet. Because I seen different lengths and I don't know which one I have

By short and long I meant Yukon or Yukon XL. I'm having reading comprehension issues again today and missed that you just want the axle shaft.

GM OE - 22874951
Dana - 2023479
Dorman - 630324
Richmond - 9225173

The 8.6" axles have 30 splines, the 9.5" axles are 33 spline.

If you were to buy a 9.5" axle from a RWD Escalade or Denali, they bolt right up, you don't even have to change the u-joint or shorten the driveshaft.

Oh, the most important number is AAM - 40019701 - That is the original piece in your truck, AAM supplied the front and rear differentials. It is 866 millimeters long. I do not know where they measure from.

What happened to your axle by the way?

 

[Warriorpluto]

Short truck body, long truck body.

Oh it's short when base

 

[Warriorpluto]

By short and long I meant Yukon or Yukon XL. I'm having reading comprehension issues again today and missed that you just want the axle shaft.

GM OE - 22874951
Dana - 2023479
Dorman - 630324
Richmond - 9225173

The 8.6" axles have 30 splines, the 9.5" axles are 33 spline.

If you were to buy a 9.5" axle from a RWD Escalade or Denali, they bolt right up, you don't even have to change the u-joint or shorten the driveshaft.

Oh, the most important number is AAM - 40019701 - That is the original piece in your truck, AAM supplied the front and rear differentials. It is 866 millimeters long. I do not know where they measure from.

What happened to your axle by the way?

If I can get one for $200 I think I'll go that route. Thanks for the information.

 

[Warriorpluto]

By short and long I meant Yukon or Yukon XL. I'm having reading comprehension issues again today and missed that you just want the axle shaft.

GM OE - 22874951
Dana - 2023479
Dorman - 630324
Richmond - 9225173

The 8.6" axles have 30 splines, the 9.5" axles are 33 spline.

If you were to buy a 9.5" axle from a RWD Escalade or Denali, they bolt right up, you don't even have to change the u-joint or shorten the driveshaft.

Oh, the most important number is AAM - 40019701 - That is the original piece in your truck, AAM supplied the front and rear differentials. It is 866 millimeters long. I do not know where they measure from.

What happened to your axle by the way?

Also what about the driveshaft yolk

 

[CaptainAmerica1]

Yes that's what I need. But about the 9.5 swap. Is it a direct fit?

Yup

 

[swathdiver]

Also what about the driveshaft yolk

It likes eggs? haha

The yokes are 1355s on both the driveshaft and the 8.6 and 9.5 axles so no need for different u-joints.

 

[Warriorpluto]

It likes eggs? haha

The yokes are 1355s on both the driveshaft and the 8.6 and 9.5 axles so no need for different u-joints.

Lol my head is kinda all over the place right now. But thanks for the information

 

[Joseph Garcia]

Lol my head is kinda all over the place right now. But thanks for the information

Assistance overload.

Take some time to digest everything, and come back with any follow-up questions that you may have.

 

[Warriorpluto]

Assistance overload.

Take some time to digest everything, and come back with any follow-up questions that you may have.

Hi I finally got the rear end in today. But I ran into a problem. The drive shaft bolt clamps aren't lining up with the rear end. The bolts aren't lining up