Recent content by YukonGold12

  1. Y

    2019 5.3 Suburban Rough idle at stop No Codes Run good though

    Any new revelations on this one? My 07 is doing very much the same thing, and I even changed my engine mounts!
  2. Y

    VLOM Gasket

    Yeah, looks like the route I am going to take is just order the entire assembly and drop it in. It will be here Wednesday so everything will be on pause till then. Thank you!
  3. Y

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    replaced the U joints yesterday on my 07 with 220k miles. No more vibrations at highway speed. Love it when things get fixed. Pulling apart the valley cover today because it’s leaking oil. The bolts didn’t even have resistance when coming out I guess that’s why. Trying to figure out how to...
  4. Y

    VLOM Gasket

    Curious if anyone has an idea on how to change the gasket on the VLOM with rivets. Pulled this guy apart because it was leaking oil down the back. New gasket from FEL-PRO MS 96871 looks like the right fit but how do I get it on . 07 Yukon xl with 220k miles.
  5. Y

    07-14 Tahoe, Yukon, Suburban Seat Gear Replacement

    I have the same problem, but with the gears that work the forward/backward track on the console side screw. I see that Gruven parts are only for the height adjustment, not the forward/backward. Are there parts for the forward/backward screws that anyone knows about?
  6. Y

    2007 Yukon xl driver seat binding up

    Hmmm ok. I thought maybe it just got out of alignment and that is why it was binding. However, it looks like the console side screw isn’t turning. Would anyone know why this is the case? Drive side door turns just fine. Console side either won’t or will very slowly if I give it a little push...
  7. Y

    2007 Yukon xl driver seat binding up

    Oh I think I figured it out? I was able to fit a 6mm and grab the slide and rotate this until it matched the other side.
  8. Y

    2007 Yukon xl driver seat binding up

    I have a driver seat of mine that was binding up when going forward and backward. After some research it seemed that the rails are out of alignment. I pulled the seat up and reseat the furthest bolts and now the side next to the door is way off. How can I adjust this?
  9. Y

    Broken Valve cover bolt

    Still holding great after a few miles. Thank you all!
  10. Y

    Broken Valve cover bolt

    And we are in! Tightened to snug and 1/8th turn more. I don’t dare tighten them further and I don’t trust my torque wrench anymore (grabbing a new one this weekend).
  11. Y

    Broken Valve cover bolt

    You can see I missed it
  12. Y

    Broken Valve cover bolt

    Well we are going in today!
  13. Y

    Broken Valve cover bolt

    Great question, I had checked the hole when I took the cover off, and it looked clear. My theory is the same as yours that it just missed the hole. It wasn't spinning loose entirely, I could feel resistance, but it gave way when I was tightening it, which made me believe I stripped it.
  14. Y

    Broken Valve cover bolt

    Ok here is what I’ve done so far. I pulled it apart and chose a different bolt from a different hole. I hand tightened then turned not even a quarter turn to snug. It’s not loose at all. I ran a chaser through the hole just to check and there was no resistance. I then put back the original...
  15. Y

    Broken Valve cover bolt

    So you don’t think I should chase it? Just pickup a new bolt and try it?
See more

Forum statistics

Threads
138,093
Posts
1,998,733
Members
103,016
Latest member
BadDaddy2003

Latest posts

Back
Top