Recent content by yooformula
-
Wolfgang twins vs Meguiar's M105/205
For use with 7424 you bought, get the Meguiar's microfiber correction kit. Hands down the easiest and best system to use for polishing your truck. Takes the guess work out for newbs learning to use to those not all familiar with pads/compounds. Comes with the pads and the polishing/finishing...- yooformula
- Post #5
- Forum: Detailing
-
Need some assistance with brakes...rears wore out in 50k miles
Yet the fronts have almost no wear on them. I have noticed that the rears create alot of brake dust but I have never known the rears to wear out before the fronts. I have to change the pads tomorrow but what else should I be looking for? 03 Yukon, EBC pads front/rear with slotted rotors up front.- yooformula
- Thread
- Replies: 0
- Forum: Tech Info
-
welding my transfer case ...
Mine has a crack and this is what I did to seal the crack over a year ago. I scrubbed the area with med grit sand paper, used some rubbing alcohol on a rag and soaked the area then heated it with a small butane torch, then used Liquid Steel. Over a year later and no leaks, sucks though that the...- yooformula
- Post #9
- Forum: General Discussion
-
HID Reverse light install
sits flush with a small gap around the lip but some black rtv around it and it seals up nicely. I've had mine for about 6 months now with no issues and I love it! They are so friggin bright, makes it easy to find at night!- yooformula
- Post #17
- Forum: Exterior
-
Do the brakes need to be pre bled via scanner/tech II?
I've bled the system several times for each wheel yet the spongy feel is still apparent.- yooformula
- Post #3
- Forum: General Discussion
-
Do the brakes need to be pre bled via scanner/tech II?
I had to replace a ton of stuff on my brakes recently but still have a bit of a spongy feel. I heard that if air got into the master, that the dealer has to pre-bleed the master with a handheld, anyone ever have to do this?- yooformula
- Thread
- Replies: 3
- Forum: General Discussion
-
DDM Tuning HID kit install
DDM kits took over a month to get mine and it bs that plugs werent included simply wires and no instructions. I ordered my last 6 sets via the link that was once posted and I get my set within 2 days max, instructions and PLUGS that make it plug n play not to mention they actually warranty bulbs...- yooformula
- Post #13
- Forum: General Discussion
-
strange rattle from front end...
a bit late but I found out that if you replace the calipers and dont insert the rubber isolators in with the caliper slide bolts that it will wiggle and make that noise. with the truck on the ground and not pressing the brake, grab the caliper and see if you can move it around, if so, then its...- yooformula
- Post #6
- Forum: Street Suspension
-
Special for Members
is the stepper motor replacement the fix for the dead speedos? mine just randomly slows down to only 10-20mph.- yooformula
- Post #10
- Forum: GM Gauge Repair
-
does my mpg seem right
that exactly what I was getting to a full tank of gas before the low gas light would come on. I did the same things you did plus swapped out all the fluids in the diffs, t-case and trans, new o2 sensors, seafoam and got a decent improvement but then I ended up swapping plugs again with a...- yooformula
- Post #41
- Forum: General Discussion
-
painted callipers
looks good but your wheels need some love and you gotta paint the rears too.- yooformula
- Post #29
- Forum: General Discussion
-
2000 fbody LS1 electric fans...$125!
sold.- yooformula
- Thread
- Replies: 0
- Forum: Parts & Accessories For Sale
-
Sidesteps?
I started using poorboy's "natural look" and was very impressed with it! I slipped one too many times using various other shit but the "natural look" left no greasy residue, wasnt slippery when wet and a single application last 2 months before a reapply. Everytime I washed the car a dry wipe...- yooformula
- Post #12
- Forum: Detailing
-
Finally upgraded my brakes!
this truck has 185k and it wouldnt surprise me if they were still stockers. I too used the yellowstuff pads for the new setup but with stainless brake lines and new oem rotors/calipers.- yooformula
- Post #17
- Forum: Exterior
-
Finally upgraded my brakes!
Finally got the rears done... When I bought my used truck the prev owner said it had new brakes all around and judging by all the work orders for stuff and how clean and obviously maintained it was, I didnt think otherwise. Well this ****** would barely stop whenever the wheels got wet so I...- yooformula
- Post #15
- Forum: Exterior
