Scrappycrow
Latest activity Postings About
-
-
Scrappycrow reacted to LSCALADE's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with
Like.
Ram 1500 wheels 18" factory 5 spoke design it was available as an option on base trucks to step up from steel to aluminum. Imposter... -
Scrappycrow reacted to Charlie207's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
I just bought some mufflers to experiment with. The MBRP muffler I removed last summer had too much drone on the highway & cruising, but...
-
Scrappycrow reacted to Sir_Hiro's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
Happy to Report that Betty did great on her first of many camping trips. Developed a clunk on the drivers front i gotta look at but...
-
Scrappycrow reacted to NickTransmissions's post in the thread GM 6L80 Transmission Information Thread with Like.
This is speculation but seems as though there's a partial restriction in your system. The shop should have flushed the lines and...
-
Scrappycrow reacted to Geotrash's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
Both shocks look good with no leaks and have been performing well, so I'm just going to replace the control arms and outer tie rod ends...
-
Scrappycrow reacted to j91z28d1's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Haha.
shops are so scumy. a friend of mine sent his wife in with her car for a recall done. they did the recall but sent a video of walking...
-
Scrappycrow posted the thread Any Advice/Experience with Cleaning A Jittery Volume Knob Encoder? in Audio & Electronics.Y'all, The volume knob of the stock radio (w/ navigation) in my '13 LTZ causes the volume to skip in large steps and/or jump...
-
Scrappycrow reacted to Jdsfx1's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
I was going to use a GMC Envoy but I thought the Yukon was just a better base. It will be a little more difficult due to the width of...
-
Scrappycrow reacted to Jdsfx1's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
It will be getting a different body. It’s getting a 1941 Cadillac and I had to change the length to accommodate the new body. I will be...
-
Scrappycrow replied to the thread Does lid on center console have a spring.The lid on my '13 LTZ has springs. They're only good for keeping the lid fully up and don't provide any "pop" when you release the latch.
-
-
Scrappycrow reacted to Tonyrodz's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
My father had one in his Bronco back in the day.
-
Scrappycrow replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.Usually, yes. I removed the sun visors in my '57 Chevy when I had the Wink in it, but the top front of the windshield in Tri-Fives is...
-
Scrappycrow replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.Agreed. If I didn't care about the functionality of the sunvisors, I'd have a 5-panel Wink in my Tahoe (and most every other vehicle)...
-
A lot of GM vehicles in Australia are marketed under the Holden brand. Granted, it's a little bit of a warmer climate, but 10w40...
-
Last year I had a long discussion with a buddy that works in the local GM service department, when I was going through my wife's...
-
-
Loading…
-
Loading…
