Recent content by middelgriff1

  1. middelgriff1

    Wheel spacers

    When you slide your wheel spacer on, the actual wheel stud from you hub will stick out farther than the spacer so you have to cut them a little shorter. Make sure that you screw your lug nut on the stud and then cut, that way when you unscrew the lug nut, it'll straighten any threads out that...
  2. middelgriff1

    Been awhile

    Where is a good place to get the gears? Im thinking 4.56? Im pretty mechanically inclined but, how bad is the install?
  3. middelgriff1

    Been awhile

    Thanks guys. 01Kon- The 35's aren't too bad with the BB tune. I've been looking around for gears but since its only a weekender/ boat hauler now, they've been on the backburner.
  4. middelgriff1

    Been awhile

    Its been a little while since I've been on the forum but here's an updated pic on the Tahoe. Added the 20s on 35s, 3" lift knuckles up front and 3" spacers in the rear. De-cranked the t-bars a little. Swapped the yellow halogen lights in the grill out for 4x round LED lights. Hope you guys like...
  5. middelgriff1

    Rear Diff rebuild

    Hey guys, so I recently replaced the pinion seal for the rear diff and after driving the truck maybe 10mi back and forth to the alignment shop I noticed that I was still leaking some diff fluid. I had the shop go ahead a replace it again because maybe I messed it up somehow but no luck and its...
  6. middelgriff1

    n-Fab Step Bars

    Im gonna fab up something similar to these. I like that they don't make the truck look like its lower. How are these mounted?
  7. middelgriff1

    02 z71 electric fan?

    A lot of people have done this mod, including me here's a link http://tahoeyukonforum.com/forum/showthread.php?t=28336
  8. middelgriff1

    Lifted FINALLY!!!!!!

    looks good!:waytogo:
  9. middelgriff1

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    thanks man, its in the works when i wrap it matte gunmetal to match the fake beadlocks
  10. middelgriff1

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Bolted up the new wheels and tires! got an alignment. They are 20" Fuel Trophys and 35x12.5 Nitto Trail Graps. Trimmed a little of the rear fenders, but finally came to the conclusion that i need to go higher. Just ordered lift spindles.
  11. middelgriff1

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Pinion seal, rear axle seal, rear rotors and pads. Ended up doing all of that because I thought my parking brake pads were gone since my parking brake was slipping. Pulled my wheel off and everything was soaked on the driver rear. Then noticed some leakage from the pinion seal.
  12. middelgriff1

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I have a 2002 coming up on 200k. Its better if you buy the upper control arms with the balljoints already installed from rock auto and lowers with them installed if your wallet can take it. I just ended up pressing the lowers myself so I didn't have to pay 5hrs mech time per side. Not a bad job...
  13. middelgriff1

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Replaced my upper control arms, lower balljoints, pitman and idler arms, sway bar bushings and links, innner and outer tie rod ends. I have my new wheel setup coming in this week and only want to have one alignment done.
  14. middelgriff1

    Rear Bumper Question

    can you run a flip up rear lic plate?
  15. middelgriff1

    Best driver's side mirror on Amazon for '02 Tahoe

    what color are yours? I have both sides from mine still
See more

Forum statistics

Threads
129,364
Posts
1,814,628
Members
92,520
Latest member
Jim2014

Latest posts

Top