- Joined
- Jun 9, 2009
- Posts
- 8,744
- Reaction score
- 605
are both sides the same from ground to fenderlip?
How much to cut?
- Thread starter O3YUKONXL
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Junior209
Full Access Member
- Joined
- May 12, 2011
- Posts
- 100
- Reaction score
- 1
On side is 32 the other side is just a little higher
OP
OP
O3YUKONXL
Full Access Member
- Joined
- May 18, 2009
- Posts
- 111
- Reaction score
- 19
Wtf?
Trimmed stops, notched cross-member, and cut 1/2 a coil out of (drivers) high side only. That side came down only 1/8" and un-cut side down 3/16". I can cut more, but not exactly what I expected. Opposite side might lower some too, but not more?
Trimmed stops, notched cross-member, and cut 1/2 a coil out of (drivers) high side only. That side came down only 1/8" and un-cut side down 3/16". I can cut more, but not exactly what I expected. Opposite side might lower some too, but not more?
- Joined
- Jun 9, 2009
- Posts
- 8,744
- Reaction score
- 605
Solid axle
springs close to eachother
this is why i cut from higher side when i do them. Another option you have is putting isolators in on higher side to keep up some
springs close to eachother
this is why i cut from higher side when i do them. Another option you have is putting isolators in on higher side to keep up some
OP
OP
O3YUKONXL
Full Access Member
- Joined
- May 18, 2009
- Posts
- 111
- Reaction score
- 19
Made sense that opposite side may come down bit too, but not more than cut side. That's illogical. And when you say re-add isolators, I hope you meant to lower side. If not, I'm worried...
- Joined
- Jun 9, 2009
- Posts
- 8,744
- Reaction score
- 605
yes lowered side sorry
OP
OP
O3YUKONXL
Full Access Member
- Joined
- May 18, 2009
- Posts
- 111
- Reaction score
- 19
6" spring.............. = driver : 32 13/16 ... pass : 32 8/16........ 5/16 diff
cut 1/2 coil
(driver only)......... = driver : 32 11/16 ... pass : 32 5/16......... 8/16 diff
add 2 isolators
(pass. only).......... = driver : 32 14/16 ... pass : 32 10/16........4/16 diff
Again, I need to get to 32" rear. Hoping to get level side/side, then match cuts. Shouldn't be this difficult.
I guess, cut more from driver side, just don't want to end up cutting too much for nothing.
I backed off hardware for upper/lower trailing arms also, and then loaded(jacked) drivers side and re-torqued = 1/16" only difference. Didn't expect much there, but running out of ideas.
cut 1/2 coil
(driver only)......... = driver : 32 11/16 ... pass : 32 5/16......... 8/16 diff
add 2 isolators
(pass. only).......... = driver : 32 14/16 ... pass : 32 10/16........4/16 diff
Again, I need to get to 32" rear. Hoping to get level side/side, then match cuts. Shouldn't be this difficult.
I guess, cut more from driver side, just don't want to end up cutting too much for nothing.
I backed off hardware for upper/lower trailing arms also, and then loaded(jacked) drivers side and re-torqued = 1/16" only difference. Didn't expect much there, but running out of ideas.
Last edited:
OP
OP
O3YUKONXL
Full Access Member
- Joined
- May 18, 2009
- Posts
- 111
- Reaction score
- 19
now what?
- Joined
- Jun 9, 2009
- Posts
- 8,744
- Reaction score
- 605
Sorry been working like crazy. Isolators on pass side and cut more from drivers. You want it lower so will need to cut more. No more then 1.5 full loop if you cut to much spring will fall out because shocks are to long
OP
OP
O3YUKONXL
Full Access Member
- Joined
- May 18, 2009
- Posts
- 111
- Reaction score
- 19
Ok, but w/ me having cut high side and added isolators to low side, and haven't changed that 1/4 - 5/16" side/side diff. Is it ever gonna go away? Also now, if I center jack middle of rear diff. ; one side lifts off before other. Used to be same time. Could something up front be the cause?
Similar threads
