Rear bumper lower trim piece?

[Myblkss99]

Thanks to the member who posted the original instructions! My install went well and completed in about 1/2 a day in the driveway. I went with all factory parts (list below) and painted the tips black with some high temp paint!

 

[23Tahoe44]

Very nice ,I Too just want to use the stock muffler, can you post some pictures of the exhaust hangers that you used , also how much did you spend on parts

 

[Myblkss99]

Very nice ,I Too just want to use the stock muffler, can you post some pictures of the exhaust hangers that you used , also how much did you spend on parts

Thanks! I dont have any good pictures of the hangers. They are very straight forward to install one retainer clip and bolt per side. They also have an alignment pin built in. Total cost was right around $1000 but that was with some rewards points and a 10% discount. Below is a pic of the parts at list price.

 

[Myblkss99]

Oh and there is a left and a right hanger

 

[olyelr]

Thanks! I dont have any good pictures of the hangers. They are very straight forward to install one retainer clip and bolt per side. They also have an alignment pin built in. Total cost was right around $1000 but that was with some rewards points and a 10% discount. Below is a pic of the parts at list price.

Looks like 20% off, no?

Anyway, it looks good! Just like it should have come! Bet it sounds better too !

 

[Myblkss99]

Very happy with the sound! It’s not like an aftermarket exhaust but a definite improvement over the old stock setup. It’s just enough.

As for the price yes it worked out to almost 20% as I had $100+ in GMC rewards points. Check the App you may have more than you think.

 

[Luckylefty]

So I went and out the new dual rear bumper cover #84751055 on my 2022 LT using the instructions shown above in this post.View attachment 371916

Where did you get the part from

 

[Luckylefty]

View attachment 305219
Installed 84751055 dual exhaust lower fascia for my RST. Now I need to figure out what exhaust I wanna install.

Where did you order the part from I’ve been looking for it

 

[Myblkss99]

Paint I used….

 

[VATahoe325]

Great guide! Installed lower fascia today and have Borla Touring sitting in garage ready for install. Does anyone have the torque spec for the rear anti sway bar? Could not not locate. Thanks!

 

[18tahoelt]

Thanks to the member who posted the original instructions! My install went well and completed in about 1/2 a day in the driveway. I went with all factory parts (list below) and painted the tips black with some high temp paint!

Want this on my 21 AT4 i just got..looks so much better with Dual!!

 

[18tahoelt]

Anyone in the Chat know if the Stock Dual exhaust from a Yukon with 6.2l will fit on a Yukon 5.3l. Getting mixed messages. Worst case could be modified to fix by a exhaust shop..Any help would be greatly appreciated

 

[K5-Z71]

Anyone in the Chat know if the Stock Dual exhaust from a Yukon with 6.2l will fit on a Yukon 5.3l. Getting mixed messages. Worst case could be modified to fix by a exhaust shop..Any help would be greatly appreciated

No, it will not work. The pipe diameter on the 6.2 is larger, studs on the mounting flange are spaced further apart as well.

A good exhaust shop can chop and weld anything you ask for!

 

[18tahoelt]

No, it will not work. The pipe diameter on the 6.2 is larger, studs on the mounting flange are spaced further apart as well.

A good exhaust shop can chop and weld anything you ask for!

Thank K5-Z71.. had a feeling that was the case. Appreciate the info..looks like I am cutting and welding!

 

[Myblkss99]

Paint I used….View attachment 406390

Update….i made it a little over a year and the paint just started to flake on the passenger side. If I were doing it over I’d use the VHT primer as well maybe that would have helped.

 

[frosted_pine_dena]

Thank you for posting pictures I just installed Vader chrome

 

[Acroston18]

Thanks to the member who posted the original instructions! My install went well and completed in about 1/2 a day in the driveway. I went with all factory parts (list below) and painted the tips black with some high temp paint!

I plan on doing the same thing. There is no modification that needs to be done, correct? The dual exhaust hooks up pretty easily? Do you have pictures of the underside where it hooks up behind the spare tire?

 

[Acroston18]

Hi all, I have a 2023 5.3L Tahoe LT. Does anyone know if the 84964238 dual exhaust will hook up with no problems or will I need to make some modifications?

 

[Chase_S]

I’m new to this forum and I would like to do the same. I recently bought a 22’ Tahoe RST. I’ve searched the part number provided in this thread and when I enter my vehicle info an asterisk comes up and it says does not fit your vehicle. Has anyone else seen this?

 

[21RST]

Im curious as well to know if it bolts up?