So I recently deleted and welded my cats due to numerous problems with replacing sensors and cost of new oem cats above my budget,
and I’m not sure if this is unrelated but while driving the last two days I’ve been repeatedly put into limp mode (stabilitrak off/engine power reduced) continuously...
So I took the z55 compressor off to inspect it due to the “service suspension” warnings I’ve had since I bought my LTZ used -
and noticed the air line to the left rear shock had been disconnected and was too taught to give it some play.
Worked that a little bit with those hose junction inside...
Dude thanks so much for this! Now I know where it is - is there any way I can access it via lowering the glovebox like on the left diagram or do I have to take the airbag out and work from there? I just got that airbag swapped from the recall at the dealer recently, go figure.*
Also, does your...
I am getting B0228-61 - for the life of me do you know where the recirculate actuator is on an ‘08 Tahoe? Is it underneath the passenger airbag by chance? I can only find the passenger and driver blend door actuators and they work fine.
Upon purchasing this used ‘08 LTZ, when getting a shop to install a new evap solenoid & charcoal canister, I mentioned to them about a suspension warning message and they took a look at it -
Upon inspection (non dealership) they noticed the compressor pump had been unplugged, and ask if I...
I’ll dm you about those extenders, there’s a lot of budget kits with just rear springs and front spindles I’m looking at just to do it cheaper. The autoride pump sounds like it works and replaced the rear shocks oem, but I’m still getting a suspension warning and that could be because the...
so you put those black spacers to make it 3”, and put in the new bump stops (I don’t want to have to do the free travel mod if at all possible) - were there any other things you have to mess with autoride in the rear? There’s a kit a little cheaper on eBay that is essentially a knock off of this...
Is there a write up on anyone who did a 2/4 or 2/3 drop on an 07-13 step by step with a kit containing front spindles, rear springs and shock relocators?
I’ve watched several youtube videos and tried to sift through here - just want a budget friendly drop that maintains Z55
(current setup is...
Hey Dustin - yeah I had the shop do it a few days after we were talking on here. It was a night and day difference, my shocks actually had travel in the front and the handling wasn't near as squirrely upfront. I'd say do it, I wasn't there more than 15 or 20 minutes at the shop. Made all the...
So I picked up an aftermarket fog light kit with oem switch for the LS - (not the GM one but Spyder automotive) - comes with fogs, wiring harness, zip ties and standard OEM light switch. Switch was easy to replace, went to start wiring the lights and after taking off the junction box lid...
Two questions:
Anyone have some luck finding nice seat covers for the '07 cloth 40/20/40 front row/second rowseats? Mine has front and second row 40/20/40 splits -
Also - Is there a way to remove the stock front console lid/fold down seat for a better console with a lid? I've seen other year...
I went ahead and got the droop stops cut...I'll post a photo so anybody else that may run into this issue can see later - Def. experienced a much different travel response almost immediately after driving away! (it helped that the lift shop had major road construction and a makeshift gravel...
Very cool - I've heard lots of good things about 5100's - i'm in a weird situation as I just bought this '07 2 months ago and the original owner had level spacers on these struts before I discarded them with these even larger spacers for the RC 3.5" lift. I haven't measured but the lift itself...
Yeah that's what I'm thinking - I know lots of lift kits where cutting these are normal procedure, and looking at it closely on both sides, I'm not really sure why the lift shop cutting only one side on both driver & passenger really does anything to alleviate the travel. My only concern as to...
Hi y'all!
So I got a 3.5" RC kit installed on the '07, love the look and have no issues running 33x12.5's on 20x10 with -19 offset.
However, when it comes to alignment, with stock struts and spacers installed within the kit, the toe is straight (it drives straight) but the caster has no room...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.