Search results

  1. J444HN

    No 4th gear despite rebuild.

    They built and fitted it. They said they’ve redone it 3 times now. Apparently.
  2. J444HN

    No 4th gear despite rebuild.

    i had my transmission rebuilt due to it slipping in 1st and 2nd. I bought a rebuilt box and it wouldn’t shift properly so just had my original rebuilt and fitted. The transmission shop had a nightmare with it and couldn’t get it to go into 4th and it’s flaring between 2-3rd. It also seems to...
  3. J444HN

    4l60e problem

    I've put it in a 2003 Steve. The valve body is also a 2003 and the 4l60 is a 1999 a second far as I'm aware, I'll check the serial numbers when I get a chance. What does low line pressure point to in terms of repairing? Valve body? Thanks for your reply!
  4. J444HN

    4l60e problem

    Thanks for the advice so far guys! I'm going to remove the shift kit I think and put a normal separator plate back in and maybe swap the valve body for one out of a known good trans. Would one from a 4L65e fit ok? The 4L60 is a 99 and the 4L65 is a 2003
  5. J444HN

    4l60e problem

    Hi Chubbs, I'm not driving the vehicle as I'm not enjoying it but now I know it can cause more damage I'll make sure it doesn't move. I'm quite competent when it comes to cars but not so much with trans but I get the feeling it's not completely scrap. I've just got a feeing that it's something...
  6. J444HN

    4l60e problem

    Hi guys, I'm hoping someone can help. I live in the UK and after my trans blowing I bought a rebuilt 4l60e online from a guy who builds them all the time apparently. Anyway, for various reasons I can't return it or contact him for that matter and the transmission isn't working as it should...
  7. J444HN

    Gas gauge showing full when it's not...

    The gauge on my truck is showing full when it's not. I know what you're thinking...stepper motors but they have all just been done. Everything was fine til my fuel pump on the tank was corroded and leaking at the top. Put a new pump and sender unit in and it was fine for a day or so then the...
  8. J444HN

    Cadillac Escalade Star Ceiling - Complete!

    I used a .75mm drill bit on a cordless drill and drilled and pushed. Go slow and it catches the material. They are very bright but mine can be set brightness and colour and it stores that each time it goes on and off so you're not doing it every time.
  9. J444HN

    Cadillac Escalade Star Ceiling - Complete!

    It's a kit anyone can buy. I bought the strands separately then I contacted a company and spec'd the light source I wanted as the normal 12v ones were single colour. So I had them make a home unit suitable for car power so that it has the various functions and colour.
  10. J444HN

    Cadillac Escalade Star Ceiling - Complete!

    Recently finished this star ceiling in my 2005 Escalalde. Done it all myself and took about 40 odd hours. 444 fibre optic strands, each one drilled, hand threaded in and hot glued in place before being trimmed flush. The control unit can be bright white, dull white, any colour and can flash...
  11. J444HN

    Remove headlining 04 Escalade

    Hi, Can anyone help by telling me how to remove the full headlining in a 2004 Escalade. It has a sunroof and roof mount dvd and screen. Thanks in advance!
  12. J444HN

    Torsion bar slipping?

    Double post.
  13. J444HN

    Torsion bar slipping?

    Left: 21 and a half inches. Right: 23 inches. And the left hand side feel like there is not much resistance when cornering, it almost just goes down as it wishes.
  14. J444HN

    Torsion bar slipping?

    So if the torsion bars aren't making the front end sag what else can be? I've replaced the air ride stuff with Bilstein about a year ago and the tie rods were done then. What else could cause the front to sag?
  15. J444HN

    Torsion bar slipping?

    But how would that affect my suspension from sagging on drivers side? I can't get it to level out and it's bottoming out. What do I need to change to get the adjustment as it seems like the bars just twisting in the LCA and slipping round.
  16. J444HN

    Torsion bar slipping?

    Need a bit of advice please guys. I have had my alignment done a few times now but the outer edge of my drivers tire is still wearing bad. And it almost feels like the two front wheels are continuously fighting against each other. Measuring the front it seems like even though I've had the...
  17. J444HN

    Where to buy torsion bars...

    Thanks for your reply. A garage told me that the bars could snap with more tension on them? Is this correct or is he not got a clue? I currently have Bilstein HD shocks that are only 6 months old. Thanks again, I appreciate you replying as I genuinely have no one here who has the knowledge you...
  18. J444HN

    Where to buy torsion bars...

    Mine has no more adjustment on the drivers side and the ride is really soft on that side and sagging down. What else can I do? I'm from Scotland so no one here has the same knowledge as you guys so I'm desperately asking for your help here. What are my options? I just assumed I had to buy...
  19. J444HN

    Where to buy torsion bars...

    Needing new torsion bars but can't find them ANYWHERE! Really don't want used parts, defeats the purpose. Any ideas?
  20. J444HN

    Torsion keys all the way in...how do I lift further?

    I've no idea what a drop spindle is haha. Is it easy enough to replace the keys then? Is it bad for the ball joints too?
  21. J444HN

    Torsion keys all the way in...how do I lift further?

    Is that difficult to do or expensive? I'm in the UK so not many places know about these. Would dropping it with the torsions after lifting it not put strain on the driveshafts and joints etc? ---------- Post added at 12:58 AM ---------- Previous post was at 12:57 AM ---------- Thanks for...
  22. J444HN

    Torsion keys all the way in...how do I lift further?

    Hey, One side of my car was sitting lower so the shop lifted that side and dropped the other side but it's rubbing the 26s now and looks like it's nose diving compared to the rear. Anyway to adjust this further seeing as my torsion bar is tightened right up on one side and can't be lifted...
  23. J444HN

    03-06 NBS Cluster LED conversion for only $50

    As above.. Can you do it so the guage is like VW? Blue with red needles? And the guage on this page with blue strips...what is that guage? Looks nice and fresh?
  24. J444HN

    Driver door ajar problem....but different!

    Have this message even with the door close and have been told it's a bad switch inside the latch which is fair enough. The problem went away for a couple weeks until tonight when I put the drivers window up it would show the driver door ajar message. But not when I done the other windows. Also...
  25. J444HN

    Led tail light

    My led tail lights work fine but when I have my foot on the brake for 30 seconds the drivers side brake light goes off for a minute then comes back on. The running lights stay on though, just the brake light goes off. Any ideas guys?

Forum statistics

Threads
129,418
Posts
1,815,755
Members
92,624
Latest member
tatheho

Latest posts

Top