Recent content by Shackman7878

  1. Shackman7878

    Motor flush

    Usually Dump a bottle right after a oil change usually I add a bottle every 2nd oil change. and just leave it until it need a oil change. DIRECTIONS: Run engine to normal operating temperature Shut off engine Pour entire contents of bottle into crankcase and drive immediately If trouble...
  2. Shackman7878

    Need to get some of the PPV adhesives off a new to us PPV

    You can use Goo Gone/adhesive remover product, Wd-40, Buffing compound, if it really on there you can use Decal Eraser Wheel. Can you PM me if you have the controller box, and the lights for the Outer Edge kit.
  3. Shackman7878

    2013 PPV side mirrors

    Your in luck I did all the research on that here: https://www.tahoeyukonforum.com/threads/adding-power-folding-mirrors.123610/#post-1634483
  4. Shackman7878

    Ssv suspension?

    I posted here about it I don't have access to Gm at this time for RPO codes but you can take a photo of the glovebox Plate and decode it online https://www.tahoeyukonforum.com/threads/2014-ppv-suspension.128307/#post-1595736
  5. Shackman7878

    Fuel Pump Module????

    07 Yukon Denali w/stock 6.2L L92 w/195k miles. No DIC or CEL. It runs great. When I ordered my pump from the dealer did not notice until I dropped the tank it did not have a level sensor something to check. Depends on what part of the US you are in might want to order a Locking tank ring and...
  6. Shackman7878

    not lift, but stretch; any options?

    Sounds like a awesome project. When I leave my current state wanted to take a 2500HD chassis and cut off X feet off the back move the axle forward. Hope to find one with a Duramax or swap a Cummins engine. Would be awesome to see a Tahoe 2500HD. I mean it would not be to hard to add some leaf...
  7. Shackman7878

    LMG to L94 swap question Smog (California)

    I don't want to deal with something I cant smog, or visiting a Referee every other day with "Fixes", Went to a local college with a Ref on site and seeing the same 8 people coming back for "Smog Tech" got the serial engine number was wrong, wrong manual transmission was down to gear ratio, One...
  8. Shackman7878

    LMG to L94 swap question Smog (California)

    my main reason for the conversion is more power LMG HP:310 Tq:335 L94 HP:403 Tq:417. block LMG Cast Iron L94 is Aluminum from a lot of spec checking there is some good and bad with this swap. For now looking at options when the LMG dies can I put a L94 or put a rebuild LMG back in. If I go...
  9. Shackman7878

    LMG to L94 swap question Smog (California)

    I have a 2013 Tahoe SSV the 5.3 LMG is on it way out. Was looking at swapping to the L94 6.2 but keep the DOD and AMF due to living in California. Question would it be a plug and play deal I can keep the LMG 5.3 tune factory tune and run the L94 6.2 engine and pass emission testing, Then once...
  10. Shackman7878

    How to lift rear wiper blade?

    I had the same issue on mine here is a Youtube Link
  11. Shackman7878

    Motor flush

    I like to use Valvemedic the Gray bottle every 2nd oil change. Worked great for for lifter noise, fixed a couple DOD lifters on this product. https://motormedic.com/products/motor-medic%C2%AE-valve-medic-oil-detergent-12oz
  12. Shackman7878

    sideview mirror codes? DL3 to DL8

    Here is a post I made about this subject with parts number and RPO codes - Might bug a admin to make a Pin on this https://www.tahoeyukonforum.com/threads/adding-power-folding-mirrors.123610/#post-1634483
  13. Shackman7878

    2014 PPV Front Seat Replacement

    Bought used leather seat covers LKQ for my Yukon XL and they dried out bad, Soon will have to order Foam and leather for both front seats here soon.
  14. Shackman7878

    Stock Mirrors to Power Folding 2007-2014

    Your in luck I did all the research on this. My Post: https://www.tahoeyukonforum.com/threads/adding-power-folding-mirrors.123610/#post-1634483
  15. Shackman7878

    Center console question

    how it looked version 1, If I get more time I might try and 3d Print something
See more

Forum statistics

Threads
134,779
Posts
1,907,924
Members
100,152
Latest member
MADDOG54

Latest posts

Top