Recent content by Saucy_Walnuts

  1. Saucy_Walnuts

    Service 4WD *FIXED*

    I swapped in a rebuilt NP8 in my 03 Yukon with no issues. I didnt need a relearn or anything and also swapped in a new ignition tumbler and ive got no codes other than constantly under "driver 2". I did use the old Encoder although it came with one. Ive had no codes. Is it actually going into...
  2. Saucy_Walnuts

    transfer case won't shift, everything replaced

    What year is it?
  3. Saucy_Walnuts

    Clunking when taking off

    Similar but its just a single clunk. Not multiple. I did just replace my front shaft. I greased it. I may need to grease my rear shaft. And it does not do it on bumps. Only after hitting the brakes.
  4. Saucy_Walnuts

    Clunking when taking off

    So my 03 Yukon 4x4 has developed a clunk when taking off after taking my foot off the brakes. It happens 1-2 seconds after. Ive checked everything i can think of nothing feels or sounds loose. Ive checked calipers, everything steering wise, torsion bar cross member mounts, trans mount (its wore...
  5. Saucy_Walnuts

    2003 GMC Yukon Rear HVAC issue

    Here is the module I got.
  6. Saucy_Walnuts

    2003 GMC Yukon Rear HVAC issue

    So continuing on with this. I had found a new module. It works. Went through the reset procedure,by pulling the files while truck is off for 30 seconds. Re inserted them, put it on heat and fan setting lowest. It did the test successfully. Both The actuators moved both directions then rested in...
  7. Saucy_Walnuts

    2003 GMC Yukon Rear HVAC issue

    Ah ok. I did try pulling the fuse and putting it back in but did not work. I'll see if I can find a new or used HVAC control module.
  8. Saucy_Walnuts

    2003 GMC Yukon Rear HVAC issue

    My 2003 GMC Yukon rear HVAC is stuck on heat. Ive cleaned the control know on the overhead console, and put a new actuator. Still nothing. The blend door is working properly when I manually move it between heat and air. Do the rear HVAC need to relearn like the front does? I do have the digital...
  9. Saucy_Walnuts

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Installed a new spindle and wheel bearing on my 03 Yukon as well as a CV axle.
  10. Saucy_Walnuts

    Service Brake Light on After doing rear brakes.

    Update: after doing some talking and digging it turns out the proportioning valve piston was too far forward causing the sensor to read wrong. After bleeding the front brakes it brought the piston back to center and light went away. Turns out this can happen when compressing caliper pistons on...
  11. Saucy_Walnuts

    Service Brake Light on After doing rear brakes.

    Did that about 5 times. No difference, but I did find out when I unplug this sensor for the proportioning valve it goes away. I do have a parts truck i could get it off of. Would i be able to "reset" or clean said valve and sensor? I think there is a piston of sorts in there from what research I...
  12. Saucy_Walnuts

    Service Brake Light on After doing rear brakes.

    On my 2003 GMC Yukon, I replaced the rear parking brake shoes and pads. I had to compress the caliper pistons to get them on with the new pads. Now I have a Service Brake System light on and not sure why. No ABS on or anything. My scan tool can't read the code that may be present. Any help would...
  13. Saucy_Walnuts

    P0800 Code Transfercase 2003 Yukon

    Transmission shifts fine, so maybe not TCM related? But I can't be certain, I'm still learning these trucks.
  14. Saucy_Walnuts

    P0800 Code Transfercase 2003 Yukon

    My 2003 GMC Yukon has developed a P0800 Code but all connections are good, it shifts through 4Lo, 4Hi, and 2wd fine. It has a newer Encoder from when I swapped transfercases about a month ago. What could possibly be the issue? Should I not be super concerned because everything works fine on the...
  15. Saucy_Walnuts

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Was not today but yesterday evening I replaced both front rotors, calipers, and pads on my 03 Yukon. The old ones were junk and the calipers were rusty as heck. So I used the nearly new calipers and pads with the new rotors off my parts frame for it. I'll say a vacuum brake bleeder is the way to...
See more

Forum statistics

Threads
138,035
Posts
1,997,525
Members
102,973
Latest member
CRN_25

Latest posts

Back
Top