Recent content by loulblades

  1. loulblades

    03 Yukon. No Start, just Click

    Glad to hear you got it worked out. This sounds like mine last winter on real cold days. After I called AAA for a jump and the guy tested the battery, he got in and tried to start it about 30 times and it finally started. He informed me he sees this often and is an indicator that the starter is...
  2. loulblades

    2004 Yukon SLT

    This could still be the connector housing. I used one similar to this which has both 4 and 7 pole. https://www.etrailer.com/Custom-Fit-Vehicle-Wiring/GMC/Yukon/2004/HM40975.html?vehicleid=20041172788
  3. loulblades

    Which OBD tool to buy with functions?

    One thing I would recommend, if you are going with the full blown system, is to have the bluetooth capability. It is really nice to be able to take the display with you when crawling under the truck and being able to trigger devices (i.e. the EGR vent valve, which I am currently working on, or...
  4. loulblades

    2004 Yukon SLT

    On the stock unit the connector with wires plugs right into the back of the trailer connector housing. The replacement I purchased had wires coming out of back of the trailer connector housing to the mating connector. Take a look at etrailer.com, that's where I get all my trailerin' stuff...
  5. loulblades

    Which OBD tool to buy with functions?

    I have a couple of scanners but I can't recommend either for a Denali. Oh sure they do a reasonable job reading engine sensors, graphing data etc but the Denali has so many more interesting things. Eventually a person with a Denali may want to be able to get down into the wheel speed sensors or...
  6. loulblades

    2004 Yukon SLT

    (2) Not sure what your symptom is for the "short" but after fighting with my trailer lights for some time I realized the trailer plug is not connected directly to the wires running to the back. It is a split connector and I replaced the portion that is bolted to the frame and all was well. (7)...
  7. loulblades

    2004 Yukon Denali front driver's wheel getting hot

    I changed the bracket and the pads (not that they needed it but I figured what the heck). After putting it together I jacked up the passenger side so I could spin the wheel to check for a warped rotor but at that point the caliper had not released enough to spin the wheel. I removed...
  8. loulblades

    2004 Yukon Denali front driver's wheel getting hot

    I will look at that later today. Was it obvious the bracket was warped (visual inspection) or were there other indicators (other than the heat)? Also you mentioned the brakes dragging. Were you able to "feel" that when driving? Thanks for the reply. Lou
  9. loulblades

    2004 Yukon Denali front driver's wheel getting hot

    To all, I haven't been here in awhile (too much work and too little time) but I am hoping someone might help me out. About 4 months ago I was driving along and started getting some funnyness from the front end. I pulled over to find my front driver's wheel very hot. The funnyness was...
  10. loulblades

    Service Stability Message & ABS Light & TC Traction Control Light

    Although I didn't read the code, I had similar fault indications showing up when one of my front wheel bearings went out on my '04 Denali.
  11. loulblades

    iPod integration Review: iSimple aka PXAMG (GM5) for the 03+

    iPod definitely PXAMG definitely not
  12. loulblades

    iPod integration Review: iSimple aka PXAMG (GM5) for the 03+

    I am glad to hear that the PXAMG is working out for some but I feel compelled to relate my experience. Installation of the PXAMG in my 2004 Yukon Denalli occurred last fall. The install was simple enough but I could not get the radio to recognize the iPod. Every once in awhile I would try...
  13. loulblades

    Remove ABS

    I never did a write up but here's what I did. 1. Ripped out the EBCM and tied off the wires (might remove them someday) 2. Made/installed a small mounting bracket for the valve. 3. Bought some short brake line to connect the proportioning valve to the master cylinder and installed...
  14. loulblades

    Remove ABS

    Are you saying you want to get rid of the ABS system? If so that is what I did but you may need to put in a proportioning valve. I got one from Summit that is adjustable so I could throw some extra bias to the rear brakes when I get around to replacing the drums with discs.
  15. loulblades

    Dual Battery

    If turning on the key to use accessories and that also turns on the relay it kind of defeats the purpose of having the batteries isolated. I think the idea of having an isolated battery setup is so the accessories can be used without running down the main battery. As far as wiring, my 96 had...
See more

Forum statistics

Threads
137,702
Posts
1,990,005
Members
102,698
Latest member
JamesinAbilene

Latest posts

Back
Top