Recent content by blackbeard_lives

  1. B

    4l80e shifter to valve body disconnect

    I dont know how my valve body became disconnected from the shifter but now i assemble and fill and test and all gears are neutral. I at least had some forward motion before. Need to research what could be wrong
  2. B

    4l80e shifter to valve body disconnect

    This is the third time ive found the shifter came unconnected from the valve body piston. I need to figure out how to keep them together.
  3. B

    4l80e wire harness connector leaking

    I think im gonna use some epoxy to seal a new wire harness. Dont want rtv melting. Any better ideas?
  4. B

    4l80e wire harness connector leaking

    Rebuilt the 4l80e in my 02 gmc 2500; new rosta wire harness; shouldnt have trusted the o-ring to seal when i plugged it in the case? It leaked so i drained the pan sorayed a can of electricla contact cleaner let it evaporate; shoved the connector back into the case and put down right stuff rtv...
  5. B

    4l80e valve body rebuild

  6. B

    4l80e valve body rebuild

    okay new problem. pump jammed nonto the turbine shaft so i had to pull the whole stack out of the transmission. before i drop this back in i noticed this bottom plate is moving around freely a lot. is there supposed to be this much freeplay for this part or do i need to take everything apart...
  7. B

    4l80e valve body rebuild

    never mind, found the check ball on the ground under the washing machine ha.
  8. B

    4l80e valve body rebuild

    yeah i've got the sure cure kit with the torlon balls, but those are smaller than the end plug ball that went missing. I only ever had 1 ball come out of my valve body, was i supposed to find two? if i buy a steel ball for a ball bearing from amazon, is it 5/16" or 3/8"? or metric?
  9. B

    4l80e valve body rebuild

    running some parts thru the washer tonight and my reverse check ball disappeared. i have the new sonnax reverse pistons but i don't think there's a check ball in that kit. was i supposed to have to reuse the old ball? i noticed in some transgo instructions it says to leave out that ball but...
  10. B

    4l80e valve body rebuild

    o shoot i shoulda looked more closely at nicks' 4l80e playlist, it's in there i just missed it, this should help a ton thanks!
  11. B

    4l80e valve body rebuild

    lastly, the rod im pointing at was the first that got the roll pin out, and when that pin came out, the spring shot the rod right out of the bore and I didn't notice which way it was oriented when in the valve body. it's almost mirror image, with the top being a longer gap that i'm pointing at...
  12. B

    4l80e valve body rebuild

    here's me holding a 4l80e afl drift in front of what i think is the afl hole, which instructions say to run the drill bit first and then the drift, and if that's done proper and cleaned the replacement is that solid silver cylinder on the right? previous sonnax toolkit owner welded a driver onto...
  13. B

    4l80e valve body rebuild

    3rd burned up for the previous owner of my 02 gmc 1500hd and i read that the sonnax sure cure valve body parts can prevent that from happening again so i got the drift and guide kit used off ebay and need to get my valve body fixed up, but i can't find youtubes or write-ups on how to do this...
  14. B

    4l80e direct clutch feeplay

    assembled the intermediate clutch, i have way too much room, ".140" so i added an old good condition steel ontop of the pressure plate between the snap ring and the thick pressure, this brought the clearance down to .40" pretty tight. I want to order an extra clutch and steel and have the...
  15. B

    4l80e direct clutch feeplay

    edit: i found the problem, my case plug for the dual feed wasn't cut down quite short enough and holding up the center support. got the snap ring in and started working on the reverse pin length, but i've noticed once in a while my reverse band catches and seizes the rotating, most of the time...
See more

Forum statistics

Threads
137,707
Posts
1,990,127
Members
102,700
Latest member
General Fodder

Latest posts

Back
Top