Recent content by _Dylan_
-
Just bought 2dr yukon what lift is this? thx
3" block=3" lift- _Dylan_
- Post #20
- Forum: Lifted Supension - Z71 & 4x4
-
OEM Fog light switch
2wd tahoes with a fog light option IIRC That particular switch will be extremely hard to find though. -
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
I was in the middle of working on it and kinked that line, so I went down to Advance and bought one. I don't even remember the brand...some chinese made one. I used their $40 off $100 online deal. Dropped the price of the condenser to $75. Not bad. I wanted to get a denso for around $65, but...- _Dylan_
- Post #5,026
- Forum: General Discussion
-
A/C system replacement with rear air, guidance please.
bro, you work in refrigeration. You should've done this a long time ago. :) Denso makes good condensers too, and they are very reasonably priced @ around $65. I read Sanden makes an upgraded compressor that isn't supposed to leak like the HT6 design. My compressor is still working, but...- _Dylan_
- Post #11
- Forum: Engine & Drivetrain
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Charged it with about 2.5 dust off cans. The air is pretty cold now. Colder than I remember it with the r134a. I wish I had a thermometer to check the vent temps. I may have to play with the amount of charge in it. Right now pressures are about 30/150psi which is low, but this refridgerant...- _Dylan_
- Post #5,023
- Forum: General Discussion
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Been working on the a/c system this week. The lower connection on the condenser was seized and I ended up twisting the line on it and kinking it. Yay, new condenser and a/c line too. Good thing is parts for this turd are cheap and it seems to be holding a vacuum just fine. I'm into it for...- _Dylan_
- Post #5,018
- Forum: General Discussion
-
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
I've done that twice already. :)- _Dylan_
- Post #4,997
- Forum: General Discussion
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
That's what I was trying to do, but the top of the core sheared off and I can't remove it now. It needs a new manifold line. When I get done moving next week I'm going to flush it, put new seals on, new drier, new orifice tube, put a vac on it, and try putting 21oz of computer duster...- _Dylan_
- Post #4,993
- Forum: General Discussion
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Went to change the leaky schrader valve on the low side a/c port, but it was completely seized and I broke the tip right off it. It ain't coming out now. The good thing is GM in their infinite brilliance designed the serives ports to be welded the manifold so I gotta replace the entire...- _Dylan_
- Post #4,984
- Forum: General Discussion
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Put some wipers on it lol. Might change the oil this weekend.- _Dylan_
- Post #4,932
- Forum: General Discussion
-
Was the condensor fan an option?
some of the heavier duty trucks had them- _Dylan_
- Post #7
- Forum: Engine & Drivetrain
-
barn door to tail gate conversion?
interesting, post more pictures please -
keyless entry
Take a paper clip and jump the #4 and #8 pins on the obd2 connector. The locks should cycle if you have keyless entry. To sync the remote, jump the two pins on the obd2 connector and wait for the locks to cycle. Then hold down the lock and unlock buttons on the remote until the locks cycle...- _Dylan_
- Post #6
- Forum: Audio & Electronics
