OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
I found mine on a website called offerupnow.com.
Last edited:
03 Tahoe project
- Thread starter 2003FatSo
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
Clean and on the grass
Last edited:
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
Ordered a short antenna with universal fit that wasn't so universal so time for the drill master. Shaved back enough of the vent cover piece to fit around the base of the antenna
The wheel bearings on driver side front went out today, going to switch out wheel hubs tomorrow. There are horrible noises coming from beneath Fatso he must have eaten Taco Bell.
The wheel bearings on driver side front went out today, going to switch out wheel hubs tomorrow. There are horrible noises coming from beneath Fatso he must have eaten Taco Bell.
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
Busy weekend. First, I needed to replace wheel hub, bearings got all funked up. I took off the wheel dust cover and painted it black to see how it would turn out. With tahoe lifted you can really see the dirty covers. I think the black paint makes it look fresher. I'll be doing all 4 corners soon and put up a pic. Also going to paint calipers red, rotors probably black. Intake was leaking air due to a gap at the throttle body so I tightened it down and closed the gap. 1.75" Wheel spacers for the rear come in this week. Next up after that is bushings and finish wheel hubs. I have the interior LEDs ready to install so that will be coming up soon also. 
Last edited:
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
This is what happens when you lift and don't get taller jack stands. Took a lot of careful consideration before deciding to support my jackstands with my weights
05Single
afraid of the dark
- Joined
- Feb 26, 2015
- Posts
- 8,183
- Reaction score
- 11,448
Yikes, be safe . I would do the same but all i have is the wife's 5lb bells lol
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
Lol. I was definitely scared to put my legs under it and put pressure with the breaker bar on the hubs. It held up pretty good, no problems. Hey, what kind of bumper lights are those where the whole assembly lights up? In your profile picture
05Single
afraid of the dark
- Joined
- Feb 26, 2015
- Posts
- 8,183
- Reaction score
- 11,448
Stock assemblies. I just cut out the drl then plugged it into the turn signal for a full row of lights. So I have no more drls, but they always go out anyway and I never really liked the look personally.
Last edited:
OP
OP
2003FatSo
Member
- Joined
- Apr 12, 2016
- Posts
- 59
- Reaction score
- 107
New tires. 305/45r22 AT Hankook Dynapro. 33" tire, 32.8" really. Drives great. Truck is a beast. In the mail I have new fog lights, 1.75" wheel spacers for rear wheels, spark plugs and wires and one more Moog wheel hub assembly for passenger front wheel. Oil change next weekend. Will be painting calipers red and other wheel well covers black once I do the work on each wheel.
Last edited:
Similar threads
