Search results

  1. EddieC

    Front suspension noise 2016 yukon xl

    I didn't see movement in mine when jacked up to unweight the suspension. Perhaps the spring action interferes. It was very obvious using the braking force on the ground though.
  2. EddieC

    Front suspension noise 2016 yukon xl

    After chasing a front end clunk in my 2008 Z71 for quite a while what I finally found was upper control arm bushings shot. The symptoms were, at first, clunk when first backing with wheels turned to right stop. More prevalent in the cold.ook it to the shop The clunk the progressed to show itself...
  3. EddieC

    Rear Control Arm Attachment Problem

    So far so good. That bracket is the least of my worries on a 16 year old truck that seems to find ways to demand my attention over the past few years.
  4. EddieC

    '08 Tahoe 4x4 Motor Mount Education

    Well, we've chased this sound around and finally found it. It is a suspension issue after all and not motor mount. The sound changed from occasional to always when backing and braking and as a mild clunk. Having someone watch the driver's side top control arm while doing that it turned out that...
  5. EddieC

    Front Upper Control Arm Bushing Replacement?

    Is the replacement nut on the ball joint special or just match the size and thread? I searched for J-42188-B tool; $400 to $900. Labor to have it done would be cheaper. Those are out of the question for my use. Pickle fork or pry bar and hammer is more my speed.
  6. EddieC

    Front Upper Control Arm Bushing Replacement?

    Thanks for the video. Blowing up the video does it appear like a near horizontal slot? If so, does that occur on both tabs near the bolt head and nut?
  7. EddieC

    Front Upper Control Arm Bushing Replacement?

    Any idea where to see a picture or diagram of the slotted holes?
  8. EddieC

    Front Upper Control Arm Bushing Replacement?

    Chasing a front suspension clunk noise ('08 Tahoe) when braking backing slowly in reverse, I found some movement in the frame attachment in an upper control arm. The control arms were replaced about 2 1/2 years and 21,000 miles ago by our shop using MOOG replacements. I can't say if it's the...
  9. EddieC

    Rear Control Arm Attachment Problem

    Full *********** weld is not appropriate for bracket connections like it would possibly be for full capacity (in line) splices. The plates in that bracket are thicker than the frame tubes ever were so there is no point in overkill on the welds. That bracket will be in the junkyard far before...
  10. EddieC

    Rear Control Arm Attachment Problem

    Rusty metal primer, what else? Actually everything exposed in the picture was painted. This matches your color preference better. Best that could be done in near freezing weather but the heat gun came in handy.
  11. EddieC

    Floor Jack Replacement Wheels?

    Thanks for that but I have beaten that exercise long ago and the importer changed hands (long ago) and it was a dead end with the new company. When I bought it I was too young to realize that a 2 3/4 ton jack was going to be an odd duck. It's a good reference though for the next jack to come.
  12. EddieC

    Floor Jack Replacement Wheels?

    Company was bye bye long ago with respect to the jacks.
  13. EddieC

    '08 Z71 Tahoe Rear Control Arm Bolt Torque Specs?

    If I were to use torque specs I'd never depend on ugga dugga. Besides, I love my split beam torque wrench so I look for excuses to go get it.
  14. EddieC

    Floor Jack Replacement Wheels?

    I'm sure you are right on the feasibility of retrofitting but I recently did some work at a friend's place and he had two high end jacks that we used at the same time. That left a positive impression. That puts a roadblock on the thought of retiring the old Beast even with a new replacement...
  15. EddieC

    Floor Jack Replacement Wheels?

    Yes, bigger diameter would help. On the support topic, having worked on our blacktop in the shade of ancient trees it's never hot enough to have an effect on support. Been here for over 40 years so that's not a concern. The thing I am trying to improve on though is maneuvering and the long...
  16. EddieC

    '08 Z71 Tahoe Rear Control Arm Bolt Torque Specs?

    That's not what I found but don't want to vouch for the information so I didn't post it. I will say that was significantly more torque with no "plus".
  17. EddieC

    Floor Jack Replacement Wheels?

    Looking on opinions on floor jack replacement wheels and castors that might be a bit happier (smoother and more cooperative) on asphalt driveways. My old Blue Beast (NAPA import) jack, probably over 35 years old and original, takes a lot of effort to move across the driveway and to get into...
  18. EddieC

    Roof Rack Rattle

    Resurrecting this for the same issue on 2008 Tahoe. The clamp downs just do not get the crossbars tight on the rails and I can wiggle them enough to show why they rattle going down the road. We have not used them much so I can't imagine there is any wear. It is not wind noise as previously...
  19. EddieC

    '08 Z71 Tahoe Rear Control Arm Bolt Torque Specs?

    Thanks, I got a link to the information elsewhere.
  20. EddieC

    There are just some days I wish I didn't turn wrenches

    Bass Ackwards?
  21. EddieC

    Rear Liftgate Glass Hinge Hardware?

    Nothing shows up on the GM parts sites, atleast in searching for my year. Nothing on RockAuto either. Maybe it's going to be a Rube Goldberg job in regards to the rubber bushings to tighten up the lateral slop. And the E clips can be found but not locally being metric. The looks I've gotten at...
  22. EddieC

    Rear Liftgate Glass Hinge Hardware?

    I can induce lateral movement in the hinges so the simplest first step is replacing the pins and especially the interior bushings. But where to get them?
  23. EddieC

    Rear Liftgate Glass Hinge Hardware?

    Our 2008 lift gate glass rattles around so I am looking for a place to get new hardware at the hinges; pins, inner rubber bushings and inside E clips, but not the hinges. The bushings are rock hard and probably shrunken a bit allowing movement. Any ideas?
  24. EddieC

    Transmission Cooling Line Repair?

    I have seen mixed reviews on those tools. Some say they fail and others swear by them. The cost would make it an on the fence decision for a one time repair.
  25. EddieC

    Transmission Cooling Line Repair?

    i'm guessing GM installs them before the body is mounted and laughs on the way out to lunch.

Forum statistics

Threads
128,785
Posts
1,805,362
Members
91,764
Latest member
tomcoop
Top