Search results

  1. K

    How are your 10 speeds doing?

    I installed the PPE pan, changed the filter and filled with Amsoil ULV. The 65k mile fluid I drained out was on the darker side but didn’t smell burnt. Didn’t smell fresh either. I was a little surprised to see the bolts holding the filter were not the silver E10 bolts I’ve seen in videos. They...
  2. K

    What did you do to your 2015-2020 K2XX Tahoe/Yukon Today?

    Yesterday I swapped the transmission pan to PPE, changed the filter and added fresh fluid. Another all day job. Doing this on jack stands really slows things down but it’s doable.
  3. K

    Wife surprised me with some swaybars for Christmas

    I always try to go through a few videos of people doing the job so I know what to expect and tools to have so I made sure I got the 36mm socket. My little 5 gallon compressor is too small to run air tools but Milwaukee M12 stubby and a couple ratchets get me through.
  4. K

    What did you do to your 2015-2020 K2XX Tahoe/Yukon Today?

    I changed the driver side motor mount yesterday and it kicked my a$$!
  5. K

    10L80 Transmission, best way to lower exhaust for PPE pan install?

    Nice. I will make that Plan A since it’s easier than dropping the Y-pipe.
  6. K

    Wife surprised me with some swaybars for Christmas

    Great to know. Do you have any tips for install on the Belltech spindles? Were the ball joints difficult to separate? I’m planning to install the Belltech kit along with the Hellwig front bar very soon. I already have the rear.
  7. K

    How are your 10 speeds doing?

    65k on my 2019 and it seems to be fine. I’m about to do a pan drop filter and fluid change. I wish I had done it sooner.
  8. K

    10L80 Transmission, best way to lower exhaust for PPE pan install?

    I thought of doing this but I don’t think it would work. The exhaust will move in unison with the transmission. I checked by watching a video where a guy replaced the transmission mount. I noticed the exhaust moved right along with it. I plan to tackle the transmission pan swap later this...
  9. K

    Brand new OEM Magnaride concerns

    UPDATE: Ride height trim reset is a must! The difference between the worn struts and new struts is major. After driving for a while with the new struts, I started to feel like something just wasn’t right. Some impacts were still just too harsh. I added a Hellwig rear sway bar shortly after the...
  10. K

    Project Carbon Next Gen 10 Speed Valve Body Kit - Finally Installed!

    I watched that interview with The Car Guy and the Next Gen engineer the other day which led me to this thread after researching the issue. Just when I thought I was done spending money on this truck, I find out about this and I’m now considering the upgrade. It’s either dump money into this...
  11. K

    Suggestions for quiet aggressive looking tread tires

    The new Bridgestone Dueler A/T Ascent has really good reviews. It’s an on road all terrain so it prioritizes highway noise and comfort. It still has the aggressive look just not quite as aggressive as some of the off road all terrains suggested. You have to sacrifice some noice for the bigger...
  12. K

    Brand new OEM Magnaride concerns

    This is more of an informational post for those that will be replacing their worn Magnaride struts and shocks with OEM. Over the past few months I noticed my ride quality decrease severely. The ride began to feel like a low rider’s hydraulics or a carriage ride as some others have described...
  13. K

    Another option for Motor/Engine mounts

    Mine are trashed at 55,000 miles. With a lightly modified 6.2 and a lead foot, I’ll tolerate the extra NVH for more durability.
  14. K

    Passenger side rear upper shock bolt - HOW??!!

    I just changed all of my dampers last week. The rears actually didn’t give me much trouble. I used a box end on the outside nut with a deep socket and 3 inch extension on the bolt from the inside. On the passenger side I went above the wiring harness but below the A/C lines. I didn’t full remove...
  15. K

    Another option for Motor/Engine mounts

    How are these holding up for you guys? I’m planning to order a set and swap them when I do the struts. They look like they will hold up much better than the stock mounts.

Forum statistics

Threads
138,035
Posts
1,997,555
Members
102,973
Latest member
CRN_25

Latest posts

Back
Top