Recent content by thill466

  1. T

    Yukon AT4 suspension issues

    Pro comp is definitely reputable! I'm not sure either, but i do know a guy on a facebook group added a non magneride kit to his at4 and had all the sensors twist and throw codes etc. Maybe call readylift and ask if they would just sell the sensor relocation brackets?
  2. T

    Yukon AT4 suspension issues

    When I was looking at levels/lifts I went with the readylift because it was well designed and included sensor and wire relocation brackets. Not trying to be rude, but this kinda looks like it could be a cheaper level kit, or potentially an installation issue?
  3. T

    Anyone Running Kings or ICONS?

    Looks great! Can you drop a part # for the upgraded rear control arms? I did the readylift kit on my wife's at4 because it was the only one that retained the magneride but it didnt come with extended rear control arms.
  4. T

    Towing up Mountain Pass - 210F Engine and 199F Transmission

    Those numbers are fine, if not great. 100 degree's over outside ambient temp while towing is normal.
  5. T

    Lifted/Leveled 2021 - Postem Up

    - 3 inch SST readylift - Fuel heater 20x9 +1 offset - Stock Wrangler AT's 275/60/20 Will run ridge grapplers or AT3's in one size up once these wear out. Even without going up in tire size, the offset change from stock wheels is causing a slight rub on the bottom front liner and plastic at...
  6. T

    Whats needed to run 33x12.50r20?

    Can you take pictures of how they trimmed the front? I have 20x9 +1mm offset with the stock 33x10.8's and have a slight rub at full lock on drivers side even with a 3 inch readylift.
  7. T

    Park assist Retro. Yukon

    Dealer called my parts are in, retrofit next week. They said 1.5 hours install time. I highly recommend calling and asking the status of your retrofit. My original dealer took my VIN and said they would call as soon as parts were available for order. I got my oil changed at a dealer closer to...
  8. T

    Park assist Retro. Yukon

    My dealer just told me my parts on order for this retrofit. 22 AT4
  9. T

    Lifted/Leveled 2021 - Postem Up

    FWIW, rough country looks like they are now offering a magneride compatible 2.5 lift with UCA's for at4 models, or any other configurations that come with Magneride and not air ride. Only difference from readylift kit seems to be the RC still uses a pre-load and strut spacer in the front where...
  10. T

    Is there a 1" or 1.5" or 2" leveling kit for '22 AT4 Yukon with magnetic ride control?

    any update @WacoYukon ?
  11. T

    Looking for thoughts on a setup..........

    @FatDog did you get the P 285/60/20 AT3's or the LT's? I'm currently between 285/60/20 AT3's or 295/60/20's that only come in LT's but would only would gain .4 on height and .3 on width over the P metric 285/60's.
  12. T

    Is there a 1" or 1.5" or 2" leveling kit for '22 AT4 Yukon with magnetic ride control?

    Sounds good. I'm looking to get that kit so if they can retain all the hardware and parts I would definitely be interested in it.
  13. T

    Will a Canadian vehicle warranty transfer to the US.

    Yes. My at4 from south Ga came from Ontario. no issues.
  14. T

    Is there a 1" or 1.5" or 2" leveling kit for '22 AT4 Yukon with magnetic ride control?

    Wanna make a deal with me for the kit?
  15. T

    Is there a 1" or 1.5" or 2" leveling kit for '22 AT4 Yukon with magnetic ride control?

    My 22 at4 is almost a full inch higher in the rear from the factory (non air ride) . The only kit I'm aware of that will work is the traxda kit. @WacoYukon what are you doing with your readylift kit?
See more

Forum statistics

Threads
134,723
Posts
1,907,069
Members
100,113
Latest member
Drybone81

Latest posts

Top