Recent content by Bex914
-
B
Snagged the cleanest 07-14 Yukon I've ever seen
Got them for $900 wheels/tires with 265/65r18 michelin primacy LTX. They were Take-offs from a 2019 Silverado with like 3 miles when they were swapped. I work at the Chevrolet dealer where I bought it. They normally sell them for around $1200 where I work- Bex914
- Post #22
- Forum: General Discussion
-
B
Snagged the cleanest 07-14 Yukon I've ever seen
Here's some interior shots of the front.- Bex914
- Post #13
- Forum: General Discussion
-
B
Snagged the cleanest 07-14 Yukon I've ever seen
Not at all. I even pressed around on the dash. It's still got flex in it. Found that 1% that's not cracked- Bex914
- Post #5
- Forum: General Discussion
-
B
Snagged the cleanest 07-14 Yukon I've ever seen
My 02 Yukon Xl had been on it's way out for a while. The transmission had been slowly developing issues with flairing on shifts. It also had existing issues I didn't care to fix so it came time to look for a new vehicle. Initially I was looking for a newer impala or lacrosse due to 3 kids in...- Bex914
- Thread
- Replies: 26
- Forum: General Discussion
-
B
Alignment after lowering?
Toe being pretty close can mean being off a couple degrees. Spec usually +or-.20 degrees total toe. Half a degree is a decent amount. I specialize in suspension and steering as a tech for a living. Even with a home job using a tape measure you can vary a good bit. Get it in for an...- Bex914
- Post #8
- Forum: Street Suspension
-
B
2005 GMC Yukon Denali Xl Diesel engine
DETAILS MAN! DETAILS! What engine, what trans, how many miles in each? Professionally converted? Your basically asking us to fill in the blanks. Try again- Bex914
- Post #3
- Forum: Engine & Drivetrain
-
B
smoke from engine and antifreeze everywhere!
Get to work replacing the water pump and thermostat. Very normal issue. I've replaced at least 20 of them at work (ASE master technician). They're about as simple as they come. First time may take you 3 hours. Long handle combination wrench and a hammer to knock the fan clutch loose...- Bex914
- Post #27
- Forum: Engine & Drivetrain
-
B
Which motor to build for 500hp
If your wantingredients good drivability and not having to deal with drivability loss from a radical cam/stall combo, 4.8L forced induction is the way to go. The 4.8L has proven many times to be a forced induction monster due to block strength and shorter stroke. Been many junk yard builds...- Bex914
- Post #5
- Forum: Engine & Drivetrain
-
B
Front Differential Housing Tube on AWD 6.0 slight...ok major problem
Incorrect. 4wd use a solenoid on the tube to engage the front differential when in Auto/4wd. However that being said they may be dimensionally the same and may work.- Bex914
- Post #4
- Forum: Engine & Drivetrain
-
B
Intro post and New to me 2002 Yukon XL
Located just north of Columbus Ohio. It was garage kept most of its life hence the lack of any larger rust areas. Still going to do the basicsame for around here like all new brake lines and hoses. I can knock those out in 4 hours so not to worried about it.- Bex914
- Post #6
- Forum: General Discussion
-
B
Intro post and New to me 2002 Yukon XL
Whats up everyone. First time poster so I'll give a little background info about myself first. ASE certified Master Tech with around 10 years in the business. Mostly worked with GM dealerships but also some performance shops and currently franchised store. Been a GM fan (specifically LS...- Bex914
- Thread
- Replies: 10
- Forum: General Discussion
