Search results
-
What did you do to your NBS GMT800 Tahoe/Yukon Today?
Replaced the drivers door latch mechanism and outside handle. tried to figure out the rear barn door removal. didn't have much luck but did end up buying a special hing pin removal tool. hopefullt it'll do the trick. The dent on the ogiginal door bugs me.- CO-Tahoe
- Post #18,974
- Forum: General Discussion
-
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Changed the shift solinoids amd the VSS, also ran down the harness and found a diconnected connector. not sure what all did it it but now it shifts like a new rig. The cluster I ended up just going down to the pull and pay and searched for one with the same mileage. finally found one and it...- CO-Tahoe
- Post #5,739
- Forum: General Discussion
-
2000 Tahoe Grill install
And here's one after I fixed the grill and installed the Brush Guard -
2000 Tahoe Grill install
Yep. Z71. It had some issues but I've been able to correct them so far. Only thing left now is a fuel pump and sending unit. Pump works but the sending unit isn't talking nice to the fuel gauge. -
What did you do to your OBS GMT400 Tahoe/Yukon Today?
Well this weekend I fixed my gauge issues, fixed my transmission shift problem, replaced the broken door handle, fixed the busted grill , installed the brush guard, shampooed the interior, and did the wheel speed sensors on my 2000 Z71 Tahoe. Nice productive weekend.- CO-Tahoe
- Post #5,735
- Forum: General Discussion
-
2000 Tahoe Grill install
Okay. Got it. "Old Body Style" I thought I was good here since mines a 2000 and that was this section. Now I know. Thanks for the heads up. -
-
2000 Tahoe Grill install
Well I went to the pull and pay and found what I needed. -
2000 Tahoe Grill install
so I noticed on my new to me Tahoe that the bottom of the grill was flopping around so pulled it off this morning and noticed that the bottom had no screws. I then noticed that there isn't a place to clip or screw it. I'm thinking that I'm missing some kind of a header bar. Here's a pic. What... -
Transmission not shifting.
My bet would be the shift solenoid inside. I had a similar issue and it turned out to be a bad connection on the wiring harness. But I was getting a service engine light and the speedometer wasn't functioning. If you end up doing the shift solenoid inside I'd suggest that you get both. From...- CO-Tahoe
- Post #2
- Forum: Engine & Drivetrain
-
Instrument cluster/Transmission shifting-Same Issue??
Well I changed the 2 shift selinoids and it was still not shifting so I started checking other things. Turns out that there was a wire that for some reason was not plugged in at the harness sitting on top of the t-case. I found the female end that was on the harness and bingo!! I fixed several...- CO-Tahoe
- Post #5
- Forum: Engine & Drivetrain
-
Instrument cluster/Transmission shifting-Same Issue??
Yeah, I was thinking that if there is an in line short maybe coming off the VSS or in the harness line it may cause some weird crap elsewhere. I am no mechanic by any means but I was just wondering and hoping it's something much simpler than a 2k transmission build. I'm hopeful that the shift...- CO-Tahoe
- Post #3
- Forum: Engine & Drivetrain
-
Instrument cluster/Transmission shifting-Same Issue??
I just purchased a 2000 Tahoe z71 knowing that it had a few issues. I have done a bit of research and there are a few right ups about a possible short causing issues with both transmission shifting as well as instrument cluster issues. What is a little strange is that the bottom portion (Oil...- CO-Tahoe
- Thread
- Replies: 6
- Forum: Engine & Drivetrain
-
Hey there from Colorado
Yeah it really is. That's why I went ahead and picked it up even though it had a few issues. I got the shift solenoids today so I'm hoping to get them installed after work tomorrow. Having some trouble finding a place to do the stepper motor(s). From what I can tell so far it seems like the...- CO-Tahoe
- Post #14
- Forum: Introduction
-
Hey there from Colorado
Finally got a couple of photos together. I still need to get the brush guard on it but figure I'll wait until I'm done fixing all the bugs first- CO-Tahoe
- Post #11
- Forum: Introduction
-
-
Hey there from Colorado
Cool, Thanks bud. I'll look into just replacing them either way if they are prone to failure.- CO-Tahoe
- Post #7
- Forum: Introduction
-
-
Hey there from Colorado
Thanks for the welcome, I'm not real sure what a stepper motor is but I will look into it. Is it common for more than one to go bad at a time or is there just one for multiple gauges? Appeciate the insight!- CO-Tahoe
- Post #4
- Forum: Introduction
-
Hey there from Colorado
I posted on the sister site and it was suggested to head on over here. Just wanted to pop in and say hey. New to the site. I just picked up a 2000 z71 for a song, but it does have a few issues that I'm trying to work through. The transmission doesn't want to shift up from 2nd gear ( I'm...- CO-Tahoe
- Thread
- Replies: 14
- Forum: Introduction
