Search results

  1. J

    Are there any differential gurus on this forum?

    I feel like if you're going to open the diff you might as well replace all the bearings or at least buy a full rebuild kit so you have everything on hand.
  2. J

    3/4 Ton Suburban Running Hot

    I agree with the fan clutch. Pretty simple fix and cheap too.
  3. J

    In a bind with my backup cam

    I wonder if anyone makes a high mount brake light with built in camera. That'd be awesome
  4. J

    Rear Brake Slider Bolts

    As long as the caliper floats properly, meaning it slides in and out just fine with little to NO play in any other direction then I'd say it's fine. As for the slider with the rubber boot on it, i wouldn't worry about where it goes since pretty much every after market slide pin I've seen...
  5. J

    Will 305/65R18 Fit?

    305mm is around 12" wide
  6. J

    Rusting Out

    Just ordered VHT Rust Converter and some wire brushes. Will try this out next week and throw a coat of rustoleum paint on it afterwards.
  7. J

    Rusting Out

    I'm going through the same thing right now. Thinking about grinding/sanding, and painting then maybe oil coating everything. But theres soo many rust products out there i want to get it right the first time.
  8. J

    E-Brake adjustable?

    There's multiple adjusters on the vehicle, at the rotor/drum which should only be used to set the shoes/drag, along the body on the drivers side just outside the frame rail which is what i'd use to set pedal stiffness.
  9. J

    Transfer Case noise after Rebuild

    Is the transfer case full?
  10. J

    Pinion noise?

    Trucks FIXED.... ******SOLUTION****** Pinion nut wasn't tight enough. I didn't have a beam torque wrench and for some reason no one near by carries them so i did it by feel. When i got under my truck i removed the drive shaft and there was noticeable in/out play in the pinion flange. So i...
  11. J

    Pinion noise?

    What i should've done was measure the preload before taking it apart, then get it back to that number. But since i don't' have a beam torque wrench anyways, I'll try it out by feel for now. From my research online it seems like I'm too loose so I'll go 1/4 turn at a time until it feels better...
  12. J

    02 Burban, 5.3 4x4 w/ 4L60E - Surging in Over Drive

    It could be plugs/wires. Even though they're new, it's always possible you got a bad part. Also, a bad coil pack could cause this.
  13. J

    Pinion noise?

    Do you know off hand what the specs are i'm trying to achieve? It's the GM 10 bolt, 3.73 gears, G80, and i believe 8.5" ring gear
  14. J

    Pinion noise?

    Can i use a beam torque wrench on the pinion with everything else in the axle or would i need to disassemble everything first?
  15. J

    Pinion noise?

    So over the weekend i replaced the transfercase input shaft seal and the rear pinion seal. I marked the pinion nut and my buddy counted the threads. When reassembling everything, my buddy thought i went past my mark by 1/8-1/4 turn but i thought i was still 3/4 turn short. After going for a...
  16. J

    Finally did my reverse camera

    I just did this to my 04 yukon xl. a 20' cable from radio shack is the perfect length. I routed the vid cable along the bumper to the drivers side. up the taillight and vent cap, down along the side storage, up to the headliner before the doors, down the a-pillar and across the dash. perfect...
  17. J

    A/C doesn't work well at idle, but AWESOME when driving

    I got my clutch at napa for $45, i think retail is like $100 tho
  18. J

    Longer shocks for 2" lift

    Anyone have the actual part number for them?(front + rear)
  19. J

    Dual Battery, Under the hood... For OFFROAD

    I put a second battery under the hood. These vehicles can come with dual batteries from the factory. There's a battery tray and everything. One problem i ran into was i couldn't find a deep cycle battery that will fit in the 2nd location so i went with a normal battery. There's a writeup...
  20. J

    where to get "Ford Keys"? (and a few more little questions)

    How are the shocks that come with that kit?
  21. J

    Longer shocks for 2" lift

    So i know everyone recommends bilstein 5100's. But is there a vehicle whose stock shocks are the same length as the bilstein's that will work with the 2" lift?
  22. J

    AC shuts down when engine bay temps increase

    Does the vehicle have a mechanical cooling fan? It could be the fan clutch going bad. It's a cheap fix. Test procedures... 1) start car and let idle 2) wait till a/c no longer blows cold 3) spray condenser with cold water 4) check for change in a/c temperature Test 2 put a piece of paper on...
  23. J

    How to install E-Fans

    Does the #42 pin have to be activated in order for the fans to work? If i were to install this, and not have time for a few weeks to get it turned on, will the fans still keep my a/c and engine cool without the use of an external on/off switch?
  24. J

    DIY front end Lift/level

    When you do ford keys, do you need new shocks or shock extensions?
  25. J

    02 Yukon Header Advice

    Post up results when/if you get them installed and such.

Forum statistics

Threads
129,251
Posts
1,812,847
Members
92,354
Latest member
Off Road Pedia

Latest posts

Top