Recent content by Turbotoys

  1. T

    best route to run a 4 gauge amp power wire

    They make water tight connectors for that - Just poke a hole with a drill and use a Liquid tight connector. The connectors that I use are for S/O cords. Look up Liquid Tight Connector for flexible cords on google - they make different sizes depending on cord diameter. Ill attach an image of what...
  2. T

    Speaker upgrade

    I'm about to change mine out as well - I got some Focal 3-ways i'm gonna put in there. I've had the door panels off a few times all ready - they are easy. I haven't taken the dash grills off yet.
  3. T

    Wiring Schematics 2015+

    Im pretty sure everything is controlled by the BCM :jester: Are you trying to add factory fog lamps?
  4. T

    Wiring Schematics 2015+

    Fog Lights Here is the Fog Lights ---------- Post added at 08:13 PM ---------- Previous post was at 07:52 PM ---------- There is only 1 Subwoofer - if you look at the diagram above there is only 1 positive and a negative for subwoofer. There must be a misprint or they are using a...
  5. T

    Wiring Schematics 2015+

    Here are the wiring schematics for the Stereo and Amp. If anyone wants any other wiring let me know and I will post em up. Radio Amp - it is located behind the jack bracket in the rear of the vehicle.
  6. T

    Added sub/ANC making a lot of noise!

    Yeah well, that's warm compared to a few days ago. It was like -40 with the wind chill and they canceled schools even. I will try to post some schematics up in the next week or two - I've been super busy lately and I will have to find the correct ones . I have around 800+ pages to comb...
  7. T

    Added sub/ANC making a lot of noise!

    Actually on the Audiocontrol DQ-61 you can tap right off the amp, it will accept up to 400watts per channel line-in. i'm not sure how many watts the Bose amp is putting out but I know it cant be over 400 watts per channel considering how small the amp is :) I just checked my Radio and In my...
  8. T

    Air Intake for 6.2

    I have that one installed on my suburban - I like it but am disappointed at the finish and quality. They are actually powder-coated chrome and the stuff chips right off so be careful when doing the install. Also, it comes with some plastic crankcase adapters and be careful installing them as...
  9. T

    Added sub/ANC making a lot of noise!

    According to the schematic, as weird as it sounds, you clipped the "Crankshaft Position Sensor Replicated Signal" wire as seen in diagram below. I was thinking of posting all of the radio schematics in a separate posting but not sure if anyone is interested in them... In my install I was...
  10. T

    Reset codes and warning lights

    Definitely in the wrong section but on my 2000 suburban I had an issue where my ABS and traction control light was on - did a brake job and the wheel speed sensors had a load of grease on them from the bearing being bad - I took them out and cleaned them and worked fine ever since. If you look...
  11. T

    2015 Suburban NEED Spindles - Information

    I would like to do the strut mod but I only have a cnc vertical mill in my garage - no lathe..... yet.... I think the spindles would be the best ride option - Plus i might later on want to add better quality lowering springs. how deep do you cut the grove? how wide? and how far from the...
  12. T

    2015 Suburban NEED Spindles - Information

    I want aftermarket 2" lowering spindles... they aint got 'em... I shoould have been more clear... lol
  13. T

    2015 Suburban NEED Spindles - Information

    Does anyone have information on when spindles will be available? I have Crown Suspension coils in my rig and they are total crap. I need to put the stock coils in - the ride is so awful and now one side is compressing more than the other by 3/4". Took it to a shop and they checked the coils and...
  14. T

    Few updates

    Where are you getting the spindles from??? I have been checking weekly everywhere i can think of. I have that crown suspension crap and need to take that junk out!!! I want the factory coils back in the front ASAP.
  15. T

    Window trim removal

    The trim is now riveted to the door and has to be drilled out to remove them - I just had to replace one that was dented from the factory. Its still pretty easy though - you'll just need a rivet gun to put them back on.
See more

Forum statistics

Threads
129,374
Posts
1,814,931
Members
92,548
Latest member
Spargewort

Latest posts

Top